Unit 2c - Never Walk Past An Unsafe Act
Unit 2c - Never Walk Past Unsafe Act
- 1.
Last year, 6% of all injuries were related to improper use of hand tools.
- A.
TRUE
- B.
FALSE
Correct Answer
B. FALSEExplanation
False 12% of all injuries last year were ralated to improper use of hand tools.Rate this question:
-
- 2.
When working around rebar it is a good idea to bend over the tie wire to avoid someone getting cut by it.
- A.
TRUE
- B.
FALSE
Correct Answer
A. TRUEExplanation
Try to coach the people installing the wire to bend it over as they go.Rate this question:
-
- 3.
What is wrong with this picture?
- A.
The worker is not tied off
- B.
Not wearing a face shield
- C.
Wrong type of groves
- D.
Both b and c
- E.
All of the above
Correct Answer
D. Both b and cExplanation
It is a good idea to wear a faceshield whenever you are using a torch, especially above your waist. Gloves should be all leather so the slag wont melt the glove to your hand. Also remember to use some form of ear protection aswell.Rate this question:
-
- 4.
When walking up to a condition like this what should you do?
- A.
Pull or bend nails
- B.
Tell someone at your next break
- C.
Immediately fix the hazard and then use the opportunity to find and educate that person on hazards.
Correct Answer
C. Immediately fix the hazard and then use the opportunity to find and educate that person on hazards.Explanation
The correct answer is to immediately fix the hazard and then use the opportunity to find and educate that person on hazards. This means that when encountering a hazardous condition, the priority should be to address it promptly to prevent any potential accidents or injuries. After fixing the hazard, it is important to take the opportunity to educate the person responsible for the condition about the potential dangers and how to avoid them in the future. This approach promotes a safe and proactive environment by addressing hazards and promoting awareness.Rate this question:
-
- 5.
Hand Injures usally happen by? (check all that apply)
- A.
Pinch points
- B.
Rigging
- C.
"Tools; hammer, saw, grinder, etc."
- D.
Crane hand signals
- E.
Lunch Breaks
Correct Answer(s)
A. Pinch points
B. Rigging
C. "Tools; hammer, saw, grinder, etc."Explanation
Hand injuries usually happen due to pinch points, rigging, and the use of tools such as hammers, saws, grinders, etc. Lunch breaks and crane hand signals are not typically associated with causing hand injuries.Rate this question:
-
- 6.
Pinning the guard of the saw is a safe way to speed up productivity when cutting.
- A.
TRUE
- B.
FALSE
Correct Answer
B. FALSEExplanation
Pinning the guard of the saw is NOT a safe way to speed up productivity when cutting. The guard is an important safety feature that is designed to protect the user from potential accidents or injuries. By pinning the guard, the user is compromising their safety and increasing the risk of accidents. It is always important to follow proper safety protocols and use tools as intended to ensure a safe working environment.Rate this question:
-
- 7.
Free cutting is a safe practice for cutting material!
- A.
TRUE
- B.
FALSE
Correct Answer
B. FALSEExplanation
The statement "Free cutting is a safe practice for cutting material" is false. Free cutting, also known as free machining, refers to the ability of a material to be machined easily and efficiently. While it may make the cutting process faster and more efficient, it does not necessarily mean that it is a safe practice. Safety in cutting materials depends on various factors such as using appropriate protective equipment, following proper procedures, and being aware of potential hazards. Therefore, the statement is false as free cutting alone does not guarantee safety.Rate this question:
-
- 8.
Is this good hand positioning?
- A.
Yes
- B.
No
Correct Answer
B. NoExplanation
It`s a good idea to keep hand away from tool. If cutting small boards, make sure that it's fasten down and keep hand clear of the blade.Rate this question:
-
- 9.
Standing above the saw while cutting gives you a good, safe view on where your cutting.
- A.
TRUE
- B.
FALSE
Correct Answer
B. FALSEExplanation
False you should never stand above the blade when cutting. It also helps to cut up-wind.Rate this question:
-
- 10.
If this person is tightening the bolt are they using the tool correctly?
- A.
Yes
- B.
No
Correct Answer
B. NoExplanation
Never pull against the adjustable part of the wrench. If this person is trying to tighten the bolt then the wrench is on incorrectly. He also has written his initials on the harness!Rate this question:
-
Quiz Review Timeline +
Our quizzes are rigorously reviewed, monitored and continuously updated by our expert board to maintain accuracy, relevance, and timeliness.
-
Current Version
-
Mar 21, 2023Quiz Edited by
ProProfs Editorial Team -
Jul 11, 2008Quiz Created by
Kiewit
Back to top