Quiz Over Drill Press Safety
Drill press safety
Questions and Answers
- 1.
Always have a scrape piece of wood under the stock that you are drilling so that you don't drill into the table.
- A.
True
- B.
False
Correct Answer
A. TrueExplanation
Having a scrap piece of wood under the stock that you are drilling serves as a protective layer between the stock and the table. This prevents the drill bit from accidentally drilling into the table surface, which could cause damage to the table or the drill bit itself. Therefore, it is important to always use a scrap piece of wood as a precautionary measure while drilling.Rate this question:
-
- 2.
Do not pull metal chips form the bit while it is moving.
- A.
True
- B.
False
Correct Answer
A. TrueExplanation
Pulling metal chips from the bit while it is moving can be dangerous and should be avoided. The rotating motion of the bit can cause the metal chips to fly off in unpredictable directions, posing a risk of injury to the person handling the bit or to others nearby. It is safer to wait for the bit to stop moving before removing any metal chips to prevent accidents and ensure personal safety.Rate this question:
-
- 3.
Small pieces of material should be clamped to the table or held in a vise.
- A.
True
- B.
False
Correct Answer
A. TrueExplanation
Small pieces of material should be clamped to the table or held in a vise to ensure stability and prevent movement during various tasks such as cutting, drilling, or sanding. This helps to maintain accuracy and safety while working with small pieces that may be difficult to control by hand alone. Clamping or using a vise provides a secure grip, reducing the risk of accidents and improving the overall quality of the work.Rate this question:
-
- 4.
It is safe to leave the chuck keys in the chuck while drilling
- A.
True
- B.
False
Correct Answer
B. FalseExplanation
Leaving the chuck keys in the chuck while drilling is not safe. The chuck key is used to tighten or loosen the jaws of the chuck, and if it is left in the chuck while drilling, it can get caught in the rotating drill bit and cause accidents or injuries. It is important to always remove the chuck key from the chuck before starting the drilling operation to ensure safety.Rate this question:
-
- 5.
It is safe to drill with bent bits on a drill press or hand drill.
- A.
True
- B.
False
Correct Answer
B. FalseExplanation
It is not safe to drill with bent bits on a drill press or hand drill. Bent bits can cause the drill to wobble or become unstable, increasing the risk of accidents and injuries. It is important to use straight and properly aligned drill bits to ensure safe and effective drilling.Rate this question:
-
- 6.
If the drill grabs the metal and spins it, you should grab the piece of metal to keep form damaging it.
- A.
True
- B.
False
Correct Answer
B. FalseExplanation
The statement suggests that if the drill grabs the metal and spins it, one should grab the piece of metal to prevent it from getting damaged. However, this is incorrect. If the drill grabs the metal, it is advisable not to grab the metal as it can lead to injury. Instead, one should turn off the drill and safely remove the metal from it.Rate this question:
-
- 7.
Use low speeds while drilling with small drill bits to prevent them from breaking.
- A.
True
- B.
False
Correct Answer
B. FalseExplanation
There is no specific mention of using low speeds while drilling with small drill bits in order to prevent them from breaking. Therefore, the statement is false.Rate this question:
-
- 8.
Use lubricants while drilling stock to prevent the bit from heating up and dulling.
- A.
True
- B.
False
Correct Answer
A. TrueExplanation
Using lubricants while drilling stock is indeed a recommended practice to prevent the bit from heating up and dulling. When drilling, friction is generated between the bit and the stock, which can cause the bit to overheat and become dull. By applying lubricants, such as oil or coolant, the friction and heat are reduced, prolonging the life of the bit and ensuring more efficient drilling. Therefore, the statement is true.Rate this question:
-
- 9.
Hold small material free handed while drilling to prevent breaking the drill bit.
- A.
True
- B.
False
Correct Answer
B. FalseExplanation
The statement suggests that it is false to hold small material free-handed while drilling to prevent breaking the drill bit. This means that it is not necessary to hold small material free-handed while drilling to prevent breaking the drill bit. There may be alternative ways to hold the material securely while drilling, such as using clamps or a vice to ensure stability and prevent accidents.Rate this question:
-
- 10.
Using gloves while using the drill is a safe thing to do.
- A.
True
- B.
False
Correct Answer
B. FalseExplanation
The statement suggests that using gloves while using a drill is a safe thing to do. However, this is not true. Wearing gloves while operating a drill can actually increase the risk of accidents. Gloves can get caught in the drill bit, leading to serious injuries. It is recommended to avoid wearing gloves while using a drill to ensure safety.Rate this question:
-
- 11.
Maintain a _______ margin of safety from the drill bit while drilling.
- A.
2"
- B.
3"
- C.
4"
- D.
5"
Correct Answer
A. 2"Explanation
To ensure safety while drilling, it is important to maintain a sufficient margin of safety from the drill bit. A margin of safety refers to the distance between the drill bit and any potential obstacles or hazards. In this case, a 2" margin of safety would be appropriate, as it provides a reasonable distance to prevent accidental contact with objects or surfaces that could cause damage or injury.Rate this question:
-
- 12.
If you drilling cylindrical stock, you should use a _________ to hold the stock firmly while drilling.
- A.
Friend
- B.
Booth hands
- C.
V- block
- D.
Round block
Correct Answer
C. V- blockExplanation
When drilling cylindrical stock, it is important to securely hold the stock in place to ensure accuracy and safety. A v-block is a tool specifically designed to hold cylindrical objects firmly and securely while drilling. It has a V-shaped groove that allows the cylindrical stock to be positioned and held securely in place. This ensures that the stock remains stable and prevents any movement or slipping during the drilling process, resulting in precise and accurate holes. Therefore, using a v-block would be the most appropriate choice for holding cylindrical stock while drilling.Rate this question:
-
- 13.
The long end of the stock should go on the ______________ of the column of the drill press.
- A.
Left
- B.
Right
- C.
Inside
- D.
Outside
Correct Answer
A. LeftExplanation
The long end of the stock should go on the left side of the column of the drill press. This is because the drill press operates with a rotating motion that moves from left to right. Placing the long end on the left side ensures that it will be properly aligned with the drill bit and allows for a smoother and more accurate drilling process.Rate this question:
-
Quiz Review Timeline +
Our quizzes are rigorously reviewed, monitored and continuously updated by our expert board to maintain accuracy, relevance, and timeliness.
-
Current Version
-
Mar 20, 2023Quiz Edited by
ProProfs Editorial Team -
Sep 07, 2010Quiz Created by
Kenbessac
- Back Safety Quizzes
- Chemistry Safety Quizzes
- Construction Safety Quizzes
- Electrical Safety Quizzes
- Fire Safety Quizzes
- Kitchen Safety Quizzes
- Laboratory Safety Quizzes
- Office Safety Quizzes
- Online Safety Quizzes
- Patient Safety Quizzes
- Safe Lifting Quizzes
- Sander Safety Quizzes
- Saw Safety Quizzes
Back to top