Trivia Quiz On Environmental Health And Safety Compliance Training
(283).jpg "Trivia Quiz On Environmental Health And Safety Compliance Training - Quiz")
Are you looking for a Trivia Quiz on Environmental Health and Safety Compliance Training? There are a lot of threats to our environment, and it is up to us to ensure that we do the most to ensure that we take care of it. The quiz below is perfectly designed to help you see how environmentally conscious you are from this training. Give it a shot!
Questions and Answers
- 1.
Because the Chemical Hygiene Plan is generic for the campus, you should inquire about specifics for your _______.
- A.
Department
- B.
Major
Correct Answer
A. DepartmentExplanation
The Chemical Hygiene Plan is a generic plan that applies to the entire campus. Therefore, to ensure that you have the necessary information and guidelines specific to your area of work or study, it is important to inquire about the specifics for your department. This will help you understand any additional protocols or precautions that may be relevant to your specific field or area of expertise.Rate this question:
-
- 2.
The fire triangle refers to a combination of fuel, _______ and a source of heat.
- A.
Water
- B.
Combustibles
- C.
Oxygen
- D.
Flammable liquid
Correct Answer
C. OxygenExplanation
The fire triangle refers to a combination of fuel, oxygen, and a source of heat. Oxygen is necessary for combustion to occur, as it acts as an oxidizer that supports the chemical reaction. Without oxygen, the fire cannot sustain itself and will be extinguished.Rate this question:
-
- 3.
Take caution around flammables and combustibles that produce more _______.
- A.
Acetone
- B.
Flames
- C.
Liquid
- D.
Vapor
Correct Answer
D. VaporExplanation
Take caution around flammables and combustibles that produce more vapor. Vapor refers to the gaseous form of a substance that is usually produced when a liquid or solid evaporates. In the context of flammables and combustibles, the production of more vapor indicates that there is a higher concentration of the substance in the air, which increases the risk of fire or explosion. Therefore, it is important to be cautious and handle these substances carefully to prevent accidents.Rate this question:
-
- 4.
Liquids with a _________ flash point are more hazardous because they can ignite under ambient conditions and room temperatures.
- A.
Higher
- B.
Lower
Correct Answer
B. LowerExplanation
Liquids with a lower flash point are more hazardous because they can ignite under ambient conditions and room temperatures.Rate this question:
-
- 5.
Which hazard class responds to conditions of shock, temperature, and pressure?
- A.
Corrosives
- B.
Reactives
- C.
Acute toxins
- D.
Carcinogens
Correct Answer
B. ReactivesExplanation
Reactives are a hazard class that responds to conditions of shock, temperature, and pressure. This class includes substances that can undergo violent reactions when exposed to these conditions, leading to explosions, fires, or the release of toxic gases. Examples of reactive substances include peroxides, water-reactive materials, and self-reactive substances. It is important to handle and store reactive materials with caution to prevent accidents and ensure safety.Rate this question:
-
- 6.
Dilute acid by carefully pouring:
- A.
Acid into water
- B.
Water into acid
Correct Answer
A. Acid into waterExplanation
When diluting acid, it is important to pour the acid into water rather than the other way around. This is because adding water to acid can cause a violent reaction, resulting in the acid splashing out and causing harm. On the other hand, pouring acid into water allows for better control of the reaction, as the acid can be slowly added to the water while stirring. This ensures that the acid is evenly distributed and minimizes the risk of a dangerous reaction.Rate this question:
-
- 7.
Which control measure can help you eliminate or reduce inhalation of fumes through the use of equipment?
- A.
Engineering
- B.
Administrative
- C.
Work practices
- D.
PPE
Correct Answer
A. EngineeringExplanation
Engineering control measures involve modifying or redesigning equipment or processes to eliminate or reduce exposure to hazards. In this case, engineering controls can be implemented to eliminate or reduce the inhalation of fumes by improving ventilation systems, using local exhaust systems, or implementing enclosed processes. These measures are considered more effective than administrative controls, work practices, or personal protective equipment (PPE) because they directly address the source of the hazard and can provide a more permanent solution.Rate this question:
-
- 8.
Which control measure can help restrict access to areas where hazardous materials are used?
- A.
Engineering
- B.
Work practices
- C.
Administrative
- D.
PPE
Correct Answer
C. AdministrativeExplanation
Administrative control measures can help restrict access to areas where hazardous materials are used. These measures involve implementing policies, procedures, and protocols to regulate and control access to these areas. This can include implementing restricted access policies, requiring specific training and authorization for entry, and implementing sign-in/sign-out procedures. By implementing administrative controls, organizations can effectively limit access to hazardous areas and ensure that only authorized personnel with the necessary training and qualifications are allowed entry.Rate this question:
-
- 9.
Where can you get more information on chemical warning properties?
- A.
Air sampling
- B.
Swipe test
- C.
Smell
- D.
MSDS
Correct Answer
D. MSDSExplanation
The correct answer is MSDS. MSDS stands for Material Safety Data Sheet, which is a document that provides detailed information about the potential hazards of a chemical, including its warning properties. It includes information on the chemical's physical and chemical properties, health effects, handling and storage procedures, and emergency response measures. Therefore, consulting the MSDS is the best way to obtain comprehensive information about the warning properties of a chemical.Rate this question:
-
- 10.
Signs and symptoms associated with chemical exposure include coughing, sneezing, difficulty breathing, and ______.
- A.
Hunger
- B.
Limping
- C.
Skin sensitivity
- D.
Decapitation
Correct Answer
C. Skin sensitivityExplanation
Chemical exposure can cause various signs and symptoms, including coughing, sneezing, and difficulty breathing. These symptoms are typically associated with irritation of the respiratory system. Skin sensitivity is another common symptom of chemical exposure, as certain chemicals can irritate and damage the skin upon contact. This can manifest as redness, itching, or a rash. Hunger and limping are unrelated to chemical exposure, while decapitation is a severe and unrelated condition.Rate this question:
-
- 11.
If there is a skin or eye exposure, flush the affected area with water for at least _____ minutes.
Correct Answer
15Explanation
If there is a skin or eye exposure, it is important to flush the affected area with water for at least 15 minutes. This duration allows for thorough rinsing of any chemicals or foreign substances that may have come into contact with the skin or eyes. Flushing with water helps to dilute and remove the harmful substances, reducing the risk of further damage or irritation.Rate this question:
- 12.
_________ and/or electrical shock can occur when power strips or outlets are overloaded.
- A.
Cryogens
- B.
Fires
- C.
Lasers
- D.
Radiation
Correct Answer
B. FiresExplanation
When power strips or outlets are overloaded, the excessive flow of electricity can generate heat. This heat can cause the insulation around the wires to melt or ignite, leading to fires. Overloading can occur when too many devices or appliances are plugged into a single power strip or outlet, exceeding its capacity to handle the electrical load. The excessive heat generated can ignite nearby flammable materials, resulting in fires. Therefore, fires can occur as a consequence of overloading power strips or outlets.Rate this question:
-
- 13.
Personal Protective Equipment (PPE) is the preferred strategy (your first resort).
- A.
True
- B.
False
Correct Answer
B. FalseExplanation
PPE is considered the strategy of last resort because of the potential for incorrect fit, use of the wrong PPE, use of damaged or poorly maintained PPE, or inconsistent PPE use.Rate this question:
-
- 14.
When working with hazardous chemicals, proper personal protective equipment includes gloves, eye protection, laboratory coat, long pants, and _____.
- A.
Closed toe shoes
- B.
Laser goggles
- C.
Lead shielding vest
- D.
Fume hood
Correct Answer
A. Closed toe shoesExplanation
When working with hazardous chemicals, it is important to protect all parts of the body, including the feet. Closed toe shoes provide a barrier between the chemicals and the feet, reducing the risk of chemical spills or splashes causing harm. Open-toed shoes or sandals would not provide adequate protection in this situation. Therefore, closed toe shoes are necessary as part of the proper personal protective equipment.Rate this question:
-
- 15.
When working with chemicals you should segregate based on the hazard ______.
- A.
Atomic structure
- B.
Class
- C.
Level
- D.
Route of entry
Correct Answer
B. ClassExplanation
When working with chemicals, it is important to segregate them based on their class. This means grouping chemicals together based on their similar properties, characteristics, or hazards. By doing so, it helps to minimize the risk of accidents or reactions that could occur when incompatible chemicals are stored or used together. Classifying chemicals allows for proper storage, handling, and disposal procedures to be followed, ensuring the safety of individuals working with them and reducing the potential for harm.Rate this question:
-
- 16.
What are the steps to take during an earthquake?
- A.
Cover, Drop and Hold On
- B.
Drop, Cover and Hold On
- C.
Hold On, Drop and Cover
Correct Answer
B. Drop, Cover and Hold OnExplanation
During an earthquake, the recommended steps to take are to first Drop to the ground, then Cover your head and neck with your arms, and finally Hold On to a sturdy object until the shaking stops. This is the correct answer because dropping to the ground reduces the risk of being knocked over and injured, covering protects your head and neck from falling objects, and holding on to something stable helps to maintain balance and prevent being thrown around.Rate this question:
-
- 17.
Which of the following is NOT an example of how to prepare before an earthquake?
- A.
Restrain chemicals by installing lips along shelves
- B.
Secure gas cylinders and equipment
- C.
Close drawers and lock cabinets
- D.
Exit the building immediately
Correct Answer
D. Exit the building immediatelyExplanation
The given options suggest ways to prepare before an earthquake, such as restraining chemicals, securing gas cylinders and equipment, and closing drawers and locking cabinets. However, the option "Exit the building immediately" does not align with preparing before an earthquake. Instead, it is a response to an earthquake that is already happening or imminent. Therefore, it is not an example of how to prepare before an earthquake.Rate this question:
-
- 18.
When using a fire extinguisher: Pull, _____, Squeeze and Sweep.
Correct Answer
aimExplanation
When using a fire extinguisher, one of the steps is to aim. This means directing the nozzle or hose of the extinguisher towards the base of the fire. By aiming properly, the user can ensure that the extinguishing agent is targeted at the source of the fire, increasing the chances of effectively extinguishing it.Rate this question:
- 19.
Limit static and repetitive work by rotating tasks, taking __________, and moving around.
- A.
Breaks
- B.
Heavier workloads
- C.
longer hours
- D.
Twisting back procedures
Correct Answer
A. BreaksExplanation
Taking breaks is suggested as a way to limit static and repetitive work, as well as to prevent fatigue and promote productivity. By incorporating regular breaks into the work routine, employees can rest and recharge, reducing the risk of injuries and musculoskeletal disorders caused by prolonged sitting or repetitive movements. Additionally, breaks allow individuals to mentally refresh themselves, enhancing focus and concentration when they return to their tasks.Rate this question:
-
- 20.
Particularly Hazardous Substances (carcinogens, reproductive toxins & acute toxins) should always be stored in labeled secondary containment and in:
- A.
A designated area
- B.
A flammable cabinet
- C.
A corrosive cabinet
- D.
On the lab bench
Correct Answer
A. A designated areaExplanation
Particularly Hazardous Substances (carcinogens, reproductive toxins, and acute toxins) should always be stored in labeled secondary containment and in a designated area. Storing these substances in a designated area ensures that they are separated from other chemicals and reduces the risk of accidental exposure or mixing with incompatible materials. It also helps in organizing and locating these substances easily when needed. Storing them in a designated area promotes safety and minimizes the potential hazards associated with these substances.Rate this question:
-
- 21.
Strong acids and bases must be stored in proper secondary containment such that a spill would be contained.
- A.
True
- B.
False
Correct Answer
A. TrueExplanation
Strong acids and bases are highly corrosive and can cause severe damage if they come into contact with skin, eyes, or other materials. Therefore, it is important to store them in proper secondary containment to prevent spills and ensure that any potential spills are contained. This helps to minimize the risk of accidents, protect the environment, and maintain a safe working environment.Rate this question:
-
- 22.
Hazardous chemical waste must be labeled with a hazardous waste tag when the ______________.
- A.
Container is full.
- B.
first drop of waste is added.
- C.
quarter ends.
- D.
pick-up is tomorrow.
Correct Answer
B. first drop of waste is added.Explanation
The hazardous waste tag must be placed on the container when the first drop of waste is added. This is important because it helps to clearly identify and communicate the presence of hazardous chemicals, ensuring proper handling and disposal procedures are followed from the very beginning.Rate this question:
-
- 23.
Food and drink are not permitted in the lab because of ___________ concerns.
- A.
Inhalation
- B.
Ingestion
Correct Answer
B. IngestionExplanation
Food and drink are not permitted in the lab because of ingestion concerns. Ingestion refers to the act of consuming or swallowing something, such as food or drink. Allowing food and drink in the lab could lead to accidental ingestion of hazardous substances or contamination of experiments. This could pose a risk to the health and safety of individuals working in the lab and potentially compromise the integrity of scientific research.Rate this question:
-
- 24.
Lab doors must always remain closed to maintain:
- A.
A warm temperature in the lab.
- B.
Sound levels below the acceptable threshold.
- C.
Negative pressure in the lab and the room's fire rating.
- D.
Just negative pressure in the lab.
Correct Answer
C. Negative pressure in the lab and the room's fire rating.Explanation
Lab doors must always remain closed to maintain negative pressure in the lab and the room's fire rating. Negative pressure is important in a lab to prevent the release of hazardous substances into the surrounding areas. It helps to contain any potential contaminants within the lab and ensure the safety of the personnel working in the lab as well as the environment. Additionally, keeping the lab doors closed helps to maintain the room's fire rating, which is crucial for fire safety and preventing the spread of fire to other areas.Rate this question:
-
- 25.
Who should you inform that you’ve completed the Lab Safety Refresher?
- A.
Family
- B.
Friends
- C.
Only coworkers need to know.
- D.
Lab Safety Coordinator / Lab Manager / Supervisor
Correct Answer
D. Lab Safety Coordinator / Lab Manager / SupervisorExplanation
You should inform the Lab Safety Coordinator, Lab Manager, or Supervisor that you have completed the Lab Safety Refresher. This is because they are responsible for ensuring the safety of the lab and its occupants, so they need to be aware of who has completed the necessary training. Family and friends do not need to know about your completion of the Lab Safety Refresher, and only coworkers who work in the lab need to be informed.Rate this question:
-
Quiz Review Timeline +
Our quizzes are rigorously reviewed, monitored and continuously updated by our expert board to maintain accuracy, relevance, and timeliness.
-
Current Version
-
Mar 21, 2023Quiz Edited by
ProProfs Editorial Team -
May 18, 2012Quiz Created by
Nmorid
- Abdomen Quizzes
- Addiction Quizzes
- Aging Quizzes
- Arthritis Quizzes
- Beauty Quizzes
- Blood Quizzes
- Body Quizzes
- Bone Quizzes
- Brain Quizzes
- Child Health Quizzes
- Dermatology Quizzes
- Digestive System Quizzes
- Disease Quizzes
- Fertility Quizzes
- First Aid Quizzes
- Hair care Quizzes
- Health And Nutrition Quizzes
- Health And Wellness Quizzes
- Health Policy Quizzes
- Health Psychology Quizzes
- Health Worldwide Quizzes
- Hearing Quizzes
- Heart Quizzes
- Hospital Quizzes
- Illness Quizzes
- Injury Quizzes
- Kidney Quizzes
- Liver Quizzes
- Lung Quizzes
- Mental Health Quizzes
- Nose Quizzes
- Nutrition Quizzes
- Obesity Quizzes
- Ophthalmology Quizzes
- Patient Quizzes
- Patient care Quizzes
- Pharmacy Quizzes
- Pregnancy Quizzes
- Puberty Quizzes
- Public Health Quizzes
- Respiratory System Quizzes
- Sleep Quizzes
- Stress Quizzes
- Surgery Quizzes
- Surgical Instruments Quizzes
- Throat Quizzes
- Weight Quizzes
- Wellness Quizzes
Back to top