Electric Solar Vehicle Championship (Esvc) Practice Test
(478).jpg "Electric Solar Vehicle Championship (Esvc) Practice Test - Quiz")
Do you have good knowledge of electric energy and its related concepts? If yes, then you must check out this Electric Solar Vehicle Championship (ESVC) practice test that we've created below for you. Here, you'll get the chance to test your understanding of electrical appliances. Answer a few questions on this test, and see how well you can score. So, are you ready to start this test? Good luck to you!
- 1.
Which system is compulsory for appropriate fusing?
- A.
Tractive system
- B.
Grounded low voltage system
- C.
Both (a) and (b)
- D.
Not compulsory
Correct Answer
C. Both (a) and (b)Explanation
Both the tractive system and the grounded low voltage system are compulsory for appropriate fusing. The tractive system refers to the system that provides power to the trains, while the grounded low voltage system is a safety measure that ensures any electrical faults are grounded and do not pose a risk. Both systems are necessary to ensure that the fusing is done correctly and to prevent any potential electrical hazards.Rate this question:
-
- 2.
Teams can use flywheels or spring to store energy as their innovation part in the vehicle.
- A.
True
- B.
False
Correct Answer
B. FalseExplanation
The statement suggests that teams can use flywheels or springs to store energy as an innovation in their vehicle. However, the correct answer is False. The statement is incorrect because flywheels and springs are not the only options for storing energy in a vehicle. There are various other methods and technologies available, such as batteries, capacitors, and fuel cells, that can be used to store energy in a vehicle.Rate this question:
-
- 3.
Which tools can teams use in allotted team pit area?a. Soldering Rodb. Battery Chargerc. Mobile/Laptop Chargerd. All of above.
- A.
Soldering Rod
- B.
Battery Charger
- C.
Mobile/Laptop Charger
- D.
All of above
Correct Answer
D. All of aboveExplanation
Teams can use all of the above tools in their allotted team pit area. This means that they can use a soldering rod to solder or repair electronic components, a battery charger to charge batteries for their devices, and a mobile/laptop charger to charge their mobile phones or laptops. Having access to all of these tools allows the teams to carry out necessary tasks and ensure that their equipment is functioning properly.Rate this question:
-
- 4.
In case of not having proper safety tools to work in Hot Pit area,
- A.
Team can borrow from other teams
- B.
Team can work in presence of organizer
- C.
Team is responsible for any loss
- D.
Team is strictly not allowed
Correct Answer
D. Team is strictly not allowedExplanation
The correct answer is "Team is strictly not allowed". This means that if the team does not have the proper safety tools to work in the Hot Pit area, they are not permitted to enter and work in that area. This could be due to the potential hazards and risks involved in working without the necessary safety equipment. It is important to prioritize safety and ensure that all team members have the appropriate tools and equipment before engaging in any potentially dangerous activities.Rate this question:
-
- 5.
What are the necessary documents does the team captain has to bring during Technical Inspection?
- A.
Driving License and Complete reports including design report
- B.
Insurance documents and Material Certificates
- C.
Data sheets of electrical components used
- D.
All of these
Correct Answer
D. All of theseExplanation
The team captain is required to bring all of the mentioned documents during Technical Inspection. This includes the driving license, complete reports including design report, insurance documents, material certificates, and data sheets of electrical components used. Bringing all of these documents ensures that the team captain is fully prepared and compliant with the necessary requirements for the inspection.Rate this question:
-
- 6.
Stages of Technical Inspection are:
- A.
Dimension, Ergonomics, Transmission and Brake, Weight test
- B.
Transmission and Brake, Cross-Pad, Dimension
- C.
Ergonomics, Cross-Pad, Transmission and Brake, Cost Report
- D.
Weight Test, Transmission and Brake, Ergonomics
Correct Answer
A. Dimension, Ergonomics, Transmission and Brake, Weight testExplanation
The correct answer is Dimension, Ergonomics, Transmission and Brake, Weight test. This is because the stages of technical inspection are typically conducted in a specific order to ensure thorough evaluation of the product. Dimension is usually the first stage, where the size and measurements of the product are checked. Ergonomics is next, which involves assessing the product's usability and comfort for the user. Transmission and Brake are then inspected to ensure proper functioning. Lastly, the Weight test is conducted to determine if the product meets weight requirements.Rate this question:
-
- 7.
Design round will be held for only those teams which have cleared their T.I., no other team will be allowed.
- A.
True
- B.
False
Correct Answer
A. TrueExplanation
The given statement states that the design round will only be conducted for teams that have cleared their T.I. This implies that teams who have not cleared their T.I. will not be allowed to participate in the design round. Therefore, the correct answer is True.Rate this question:
-
- 8.
Teams should also prepare the cost report and present it along with the original bill.
- A.
True
- B.
False
Correct Answer
A. TrueExplanation
Teams should prepare the cost report and present it along with the original bill. This means that it is necessary for teams to not only have the original bill but also a detailed cost report that outlines the expenses incurred. By presenting both documents, teams can provide a comprehensive overview of the costs involved, ensuring transparency and accuracy in financial reporting.Rate this question:
-
- 9.
How many attempts will be given to pass the Brake Test?
- A.
2
- B.
3
- C.
4
- D.
5
Correct Answer
A. 2 -
- 10.
Cross-Pad round is to check the ________ of the Vehicle.
- A.
Maneuverability
- B.
Handling, Cornering
- C.
Acceleration, Braking
- D.
All of the above
Correct Answer
D. All of the aboveExplanation
The Cross-Pad round is designed to assess the overall performance and capabilities of the vehicle. It evaluates its maneuverability, which refers to how easily and effectively the vehicle can be controlled and navigated. It also tests the vehicle's handling and cornering abilities, which determine its stability and control while taking turns. Additionally, the round assesses the vehicle's acceleration and braking capabilities, which are crucial for its speed control and stopping power. Therefore, the correct answer is "All of the above" as the Cross-Pad round checks all these aspects of the vehicle's performance.Rate this question:
-
- 11.
A team will not be allowed to participate in event If they exceed the solar panel more than…..
- A.
12 inches
- B.
10 inches
- C.
8 inches
- D.
15 inches
Correct Answer
B. 10 inchesExplanation
If a team exceeds the solar panel by more than 10 inches, they will not be allowed to participate in the event. This suggests that there are specific regulations or limitations in place regarding the size or dimensions of the solar panel that teams must adhere to in order to be eligible to participate.Rate this question:
-
- 12.
Wheel diameter for adventure class should be in range of
- A.
25.4cm 30.48cm
- B.
20cm31cm
- C.
25.4cm 30.48cm
- D.
25cm30cm
Correct Answer
C. 25.4cm 30.48cmExplanation
The correct answer is 25.4cm to 30.48cm. This range of wheel diameter is suitable for adventure class, as it provides a good balance between stability and maneuverability. Wheels within this range are large enough to handle rough terrains and obstacles encountered during adventure activities, while still being manageable for the rider.Rate this question:
-
- 13.
Minimum Wheelbase for ESVC18 Solar Car is
- A.
65 inches
- B.
60 inches
- C.
70 inches
- D.
50 inches
Correct Answer
B. 60 inchesExplanation
The minimum wheelbase for the ESVC18 Solar Car is 60 inches. The wheelbase refers to the distance between the centers of the front and rear wheels of a vehicle. In this case, the ESVC18 Solar Car must have a minimum wheelbase of 60 inches to meet the required specifications. A wheelbase of 65 inches, 70 inches, or 50 inches would not meet the minimum requirement.Rate this question:
-
- 14.
In case of 3 wheeled Adventure Solar Car, Which shape is allowed:
- A.
Tadpole Shape
- B.
Delta Shape
Correct Answer
A. Tadpole ShapeExplanation
The correct answer is Tadpole Shape. In the case of a 3-wheeled Adventure Solar Car, the Tadpole Shape is allowed. The Tadpole Shape refers to a configuration where the two wheels are located at the front of the vehicle, while the single wheel is positioned at the rear. This shape offers better stability and maneuverability, making it suitable for an adventure solar car. On the other hand, the Delta Shape, which has a single wheel at the front and two wheels at the rear, is not allowed in this scenario.Rate this question:
-
- 15.
Minimum wall thickness of Tube Cross section used for chassis is:
- A.
1 mm
- B.
1.3 mm
- C.
1.5 mm
- D.
0.8 mm
Correct Answer
A. 1 mmExplanation
The minimum wall thickness of the tube cross section used for the chassis is 1 mm. This means that the thickness of the tube's walls must be at least 1 mm in order to meet the required strength and structural integrity for the chassis. A thicker wall provides more support and durability, ensuring the chassis can withstand various forces and vibrations during operation.Rate this question:
-
- 16.
More than one material used for vehicle chassis is
- A.
Allowed
- B.
Not allowed
Correct Answer
A. AllowedExplanation
The use of more than one material for vehicle chassis is allowed. This means that manufacturers have the flexibility to combine different materials such as steel, aluminum, and carbon fiber to design and construct the chassis of a vehicle. This allows for a balance between strength, weight, and cost considerations, resulting in improved performance and fuel efficiency. Additionally, using multiple materials can also enhance safety features and provide better structural integrity to withstand different types of impacts.Rate this question:
-
- 17.
Failing of producing the Material certificate at the time of inspection, Technical Inspector will
- A.
Pass the vehicle with Penalty
- B.
Disqualify
- C.
Either (a) or (b)
- D.
None
Correct Answer
C. Either (a) or (b)Explanation
If the material certificate is not produced at the time of inspection, the Technical Inspector can either pass the vehicle with a penalty or disqualify it. This means that the inspector has the authority to choose between these two options depending on the severity of the situation or any other relevant factors.Rate this question:
-
- 18.
Hitch point will be used
- A.
To attach push rod
- B.
On the bumper only
- C.
Same as Jack Point
- D.
Both (a) and (b)
Correct Answer
A. To attach push rodExplanation
The hitch point will be used to attach the push rod. This suggests that the hitch point is a specific location on a vehicle where the push rod can be connected or attached. It implies that the push rod serves a purpose related to the hitch point, such as providing support or leverage. The other options, "On the bumper only" and "Same as Jack Point," do not provide a clear explanation of how the push rod is used or connected. Therefore, the correct answer is to attach the push rod.Rate this question:
-
- 19.
There should be impact bumper on
- A.
Front of the vehicle
- B.
Rear of the vehicle
- C.
Front and rear of vehicle
- D.
Not compulsory
Correct Answer
C. Front and rear of vehicleExplanation
The correct answer is front and rear of vehicle. This is because impact bumpers are designed to absorb the energy of a collision and protect the vehicle's structure and occupants. Having impact bumpers both at the front and rear of the vehicle ensures that it is equally protected in case of a collision from either direction.Rate this question:
-
- 20.
The steering wheel should be
- A.
Below shoulder line and above abdomen of the driver
- B.
Above shoulder line and above abdomen of the driver
- C.
Above shoulder line and below abdomen of the driver
- D.
Below shoulder line and below abdomen of the driver
Correct Answer
A. Below shoulder line and above abdomen of the driverExplanation
The correct answer is below shoulder line and above abdomen of the driver. This positioning ensures that the driver has proper control and leverage over the steering wheel while also maintaining a safe and comfortable driving position. Placing the steering wheel below the shoulder line allows for easier and more natural arm movements, while positioning it above the abdomen prevents any interference with the driver's legs and ensures that the airbag can effectively deploy in case of an accident.Rate this question:
-
- 21.
As per rulebook, Distance between the driver’s back and Roll Hoop is
- A.
At least 1 inches
- B.
At least 2 inches
- C.
Not defined
- D.
At most 4 inches
Correct Answer
B. At least 2 inchesExplanation
The correct answer is "at least 2 inches." According to the rulebook, there is a minimum distance requirement of 2 inches between the driver's back and the Roll Hoop. This distance ensures the safety of the driver in case of any impact or collision.Rate this question:
-
- 22.
The seat belt should be of minimum
- A.
4 point Harness
- B.
5 point harness
- C.
3 point harness
- D.
6 point harness
Correct Answer
B. 5 point harnessExplanation
A 5 point harness is the correct answer because it provides the maximum level of safety and security for the occupant. It consists of two shoulder straps, two waist straps, and a crotch strap, which distribute the force of impact evenly across the body. This design helps to minimize the risk of injury by preventing the occupant from being thrown forward or out of the seat during a collision or sudden stop. Additionally, the 5 point harness is adjustable to ensure a snug fit and can accommodate different body sizes and types.Rate this question:
-
- 23.
Which seat belt is strictly not allowed during the event?
- A.
Seat belt with pull up adjuster
- B.
Seat belt with pull down adjuster
- C.
OEM Seat belt
- D.
Both (b) and (c)
Correct Answer
C. OEM Seat beltExplanation
The OEM seat belt refers to the original equipment manufacturer seat belt, which is the seat belt that comes with the vehicle from the factory. This seat belt is not allowed during the event because it may not meet the specific safety requirements or regulations for the event. Seat belts with pull up or pull down adjusters are not mentioned as being strictly not allowed, so they may be permitted during the event.Rate this question:
-
- 24.
The firewall material must be
- A.
Rigid, non permeable
- B.
Hard, non permeable
- C.
Rigid, permeable and fire resistant
- D.
Ductile, permeable and electrical resistant
Correct Answer
A. Rigid, non permeableExplanation
The firewall material must be rigid and non-permeable in order to effectively prevent the spread of fire and smoke between different areas or compartments. Rigid materials ensure that the firewall remains intact and does not collapse under fire conditions, while non-permeable materials prevent the passage of flames, gases, and smoke. This helps to contain the fire and protect adjacent areas.Rate this question:
-
- 25.
Welding of the firewall on the frame is
- A.
Acceptable
- B.
Not acceptable
- C.
Based on Permission of Jury Members
- D.
Not defined
Correct Answer
A. AcceptableExplanation
The welding of the firewall on the frame is considered acceptable.Rate this question:
-
- 26.
Floor closeout should be attached to the frame using
- A.
Fasteners
- B.
Mechanical locks
- C.
Nylon ties
- D.
Both (a) & (b)
Correct Answer
A. FastenersExplanation
Fasteners are used to attach the floor closeout to the frame. Fasteners are hardware devices that mechanically join or affix two or more objects together. They provide a secure and reliable connection between the floor closeout and the frame, ensuring that it stays in place. Mechanical locks, on the other hand, are also a type of fastener that provides additional security by interlocking the components. Nylon ties, although commonly used for cable management, may not provide the same level of strength and durability as fasteners or mechanical locks. Therefore, the most appropriate choice for attaching the floor closeout to the frame would be fasteners.Rate this question:
-
- 27.
Which type of steering wheel is allowed.
- A.
“H” Wheel
- B.
Cut-out Wheel
- C.
“Figure 8
- D.
None of these
Correct Answer
D. None of theseExplanation
None of the given options is allowed as a type of steering wheel. The options mentioned, such as "H" Wheel, cut-out Wheel, and "Figure 8", do not correspond to any recognized or standard types of steering wheels. Therefore, none of these options can be considered as an allowed type of steering wheel.Rate this question:
-
- 28.
Teams are allowed to use any kind of steering system. There is also no restriction on steering ratio.
- A.
True
- B.
False
Correct Answer
A. TrueExplanation
The given statement suggests that teams participating in a certain activity have the freedom to choose any type of steering system for their vehicles. Additionally, there are no limitations or regulations imposed on the steering ratio. Therefore, the statement is true as it confirms the absence of restrictions on the type of steering system and steering ratio that teams can utilize.Rate this question:
-
- 29.
The brake pedal shall be designed to withstand a force of
- A.
2000 N
- B.
3000 N
- C.
1500 N
- D.
2250 N
Correct Answer
A. 2000 NExplanation
The brake pedal should be designed to withstand a force of 2000 N because this force is the most appropriate and safe limit for the pedal to endure. This force is strong enough to effectively stop the vehicle but not too excessive to cause damage or discomfort to the driver. It ensures that the brake pedal is durable and reliable during emergency braking situations.Rate this question:
-
- 30.
The distance between centers of both lights is
- A.
500 mm
- B.
400 mm
- C.
600 mm
- D.
450 mm
Correct Answer
A. 500 mmExplanation
The distance between the centers of both lights is 500 mm. This means that there is a gap of 500 mm between the centers of the two lights.Rate this question:
-
- 31.
Solar Panel’s dimension must not exceed
- A.
Front bumper
- B.
Rear bumper
- C.
Impact zone
- D.
All of the above
Correct Answer
D. All of the aboveExplanation
The correct answer is "All of the above". This means that the dimensions of the solar panel must not exceed the dimensions of the front bumper, rear bumper, or impact zone. It is important for the solar panel to fit within these areas to ensure proper installation and functionality without interfering with the vehicle's design or safety features.Rate this question:
-
- 32.
Teams can change the battery set
- A.
Before the Endurance Round
- B.
In between Endurance Round
- C.
After the Break Test
- D.
None of these
Correct Answer
D. None of theseExplanation
The question asks about when teams can change the battery set. However, the given options do not provide a correct answer. The question is incomplete or not readable as it does not provide any alternative options that could be the correct answer. Therefore, an explanation cannot be generated.Rate this question:
-
- 33.
For Battery Cover, Material can be used is
- A.
Fire Resistant Flexible Rubber
- B.
Fire resistant plastic sheets
- C.
Sheet metal with insulating coating
- D.
All of Above
Correct Answer
C. Sheet metal with insulating coatingExplanation
Sheet metal with insulating coating can be used as the material for a battery cover. This option provides both the strength and durability of sheet metal, as well as the added protection of an insulating coating. The insulating coating helps to prevent any electrical conductivity or short circuits that could occur if the metal came into direct contact with the battery. Therefore, sheet metal with an insulating coating is a suitable choice for a battery cover material.Rate this question:
-
- 34.
Battery Level Indicator should completely show the
- A.
Percentage of the battery charge
- B.
Voltage of Battery
- C.
Time of remaining battery charge
- D.
Power of battery
Correct Answer
A. Percentage of the battery chargeExplanation
The correct answer is "Percentage of the battery charge" because a battery level indicator is designed to display the remaining charge as a percentage. This allows users to easily understand how much battery life is left and plan accordingly. The other options mentioned, such as voltage, time remaining, and power, are not typically displayed on a battery level indicator.Rate this question:
-
- 35.
Which components can be used as the border between tractive and GLV systems for galvanic isolation between both systems.
- A.
Charge Controller
- B.
Motor Controller
- C.
MPPT
- D.
DC-DC Convertor
Correct Answer
B. Motor ControllerExplanation
The motor controller can be used as the border between tractive and GLV systems for galvanic isolation between both systems. This is because the motor controller is responsible for controlling the power and operation of the motor, and it can effectively separate the tractive system (which powers the motor) from the GLV system (which controls other vehicle functions). By using the motor controller as the border, any potential electrical faults or issues in one system will not affect the other system, ensuring safety and proper functioning of both systems.Rate this question:
-
- 36.
How many fixed Motors are allowed?
- A.
2 Motors are allowed but with total Power should not exceed specified power in rulebook
- B.
Only one motor is allowed
- C.
2 motors are allowed
- D.
No. of Motors allowed with total Power should not exceed specified power in rulebook
Correct Answer
B. Only one motor is allowedExplanation
The given correct answer states that only one motor is allowed. This means that the maximum number of fixed motors that can be used is one. There is no allowance for using multiple motors in this scenario.Rate this question:
-
- 37.
Throttle paddle allowed in Vehicle must be
- A.
Foot operated with positive lock
- B.
Foot operated only
- C.
Hand Operated with positive lock
- D.
Right foot operated only
Correct Answer
A. Foot operated with positive lockExplanation
The throttle paddle in a vehicle must be foot operated with a positive lock. This means that the driver should be able to control the throttle using their foot, and there should be a mechanism in place to prevent accidental movement or disengagement of the throttle. This is important for safety reasons, as it ensures that the driver has full control over the acceleration of the vehicle and can securely lock the throttle in position when necessary.Rate this question:
-
- 38.
If a Team exceeds the weight limit, They will
- A.
Get zero point for weight test
- B.
Be disqualified
- C.
Get penalty in total points
- D.
None
Correct Answer
A. Get zero point for weight testExplanation
If a team exceeds the weight limit, they will receive zero points for the weight test. This suggests that the weight test is a crucial component of the evaluation, and teams must adhere to the specified weight limit to earn any points in this particular test. Exceeding the weight limit indicates a failure to meet the requirements, resulting in a penalty of zero points for this specific test.Rate this question:
-
- 39.
For using Seamless pipe, Team will be
- A.
Penalized
- B.
Disqualified
- C.
Qualified
- D.
None of above
Correct Answer
B. DisqualifiedExplanation
If the team uses a seamless pipe, they will be disqualified. This suggests that the use of a seamless pipe is not allowed or is against the rules of the competition or task at hand.Rate this question:
-
- 40.
Members of Chassis can be made up of
- A.
Solid Bars
- B.
Rectangular Bar
- C.
Circular cross section
- D.
Any shape
Correct Answer
C. Circular cross sectionExplanation
Chassis members can be made up of a circular cross section because this shape offers structural strength and stability. Circular cross sections distribute stress evenly, making them ideal for supporting heavy loads and resisting deformation. Additionally, circular shapes are easy to manufacture and provide uniformity in design, allowing for efficient assembly and integration within the chassis structure.Rate this question:
-
- 41.
How many jack points are compulsory in ESVC18 Vehicle
- A.
Two in orange color
- B.
One at front in orange color
- C.
One at rear in green color
- D.
Only one
Correct Answer
A. Two in orange colorExplanation
The ESVC18 Vehicle requires two jack points in orange color. This means that there are two specific areas on the vehicle where a jack must be placed in order to safely lift and support the vehicle. These jack points are likely indicated by orange markings or labels to ensure proper usage.Rate this question:
-
- 42.
The distance between tip of the roll hoop to tip of driver’s Helmet should be
- A.
Less than 4 inches
- B.
More than 4 inches
- C.
More than and equal to 4 inches
- D.
Equal to 4 inches
Correct Answer
C. More than and equal to 4 inchesExplanation
The distance between the tip of the roll hoop and the tip of the driver's helmet should be more than and equal to 4 inches. This means that the minimum acceptable distance between these two points is 4 inches, but it can also be greater than 4 inches.Rate this question:
-
- 43.
A team can use Impact attenuator act as a Bumper.
- A.
If It should be made up of proper crushable material
- B.
If Team submit a report stating validity of the impact attenuator
- C.
If approved by Judging Team of ISIEINDIA
- D.
All of above
Correct Answer
D. All of aboveExplanation
The correct answer is "All of the above". This means that all of the statements mentioned in the question are true. A team can use an impact attenuator as a bumper if it is made up of proper crushable material. Additionally, the team needs to submit a report stating the validity of the impact attenuator, and it should be approved by the Judging Team of ISIEINDIA. Therefore, all of these conditions must be met for the team to be able to use the impact attenuator as a bumper.Rate this question:
-
- 44.
The egress should be
- A.
Maximum 20 sec
- B.
Maximum 10 sec
- C.
Maximum 15 sec
- D.
Maximum 5 sec
Correct Answer
C. Maximum 15 secExplanation
The correct answer is "Maximum 15 sec" because it indicates the maximum amount of time allowed for egress, which refers to the process of exiting a building or a space. This means that individuals should be able to leave the area within 15 seconds, ensuring a quick and efficient evacuation in case of an emergency.Rate this question:
-
- 45.
One of the following will be considered as seat belt during event
- A.
Side release buckle straps
- B.
Belts with metal cum lock buckles
- C.
Normal shoulder straps
- D.
None of the above
Correct Answer
D. None of the aboveExplanation
None of the options mentioned (side release buckle straps, belts with metal cum lock buckles, normal shoulder straps) will be considered as a seat belt during the event. This implies that there is another type of seat belt that is not listed in the options provided.Rate this question:
-
- 46.
Driver must have a vision range of
- A.
100 degree
- B.
250 degree
- C.
200 degree left and 200 degree right
- D.
100 degree left and 100 degree right
Correct Answer
D. 100 degree left and 100 degree rightExplanation
The driver must have a vision range of 100 degrees to the left and 100 degrees to the right. This means that the driver should be able to see objects or obstacles within a range of 100 degrees on both sides of the vehicle. Having this vision range ensures that the driver has a wide field of view and can effectively monitor their surroundings while driving.Rate this question:
-
- 47.
Multiple panels may be used to form the firewall.
- A.
True
- B.
False
Correct Answer
A. TrueExplanation
The statement suggests that it is possible to use multiple panels to create a firewall. This implies that a firewall can be constructed by combining different panels, which can be advantageous in terms of flexibility and customization. It allows for the creation of a firewall that fits the specific needs and requirements of a particular environment or situation. Therefore, the answer is true.Rate this question:
-
- 48.
Separate Cover should be used for wheel cover.
- A.
True
- B.
False
Correct Answer
B. FalseExplanation
The statement suggests that a separate cover should be used for the wheel cover, which implies that there should be two covers for the wheel. However, this is contradictory and does not make sense. A wheel cover is typically a single cover that is used to protect and enhance the appearance of the wheel. Therefore, the correct answer is false, as there is no need for a separate cover for the wheel cover.Rate this question:
-
Quiz Review Timeline +
Our quizzes are rigorously reviewed, monitored and continuously updated by our expert board to maintain accuracy, relevance, and timeliness.
-
Current Version
-
Mar 17, 2023Quiz Edited by
ProProfs Editorial Team -
Oct 08, 2017Quiz Created by
ISIEINDIA
- Aptitude Test Quizzes
- Course Test Quizzes
- Driving Test Quizzes
- English Test Quizzes
- FCAT Quizzes
- General Knowledge Quizzes
- Intelligence Test Quizzes
- Medical Test Quizzes
- Mock Test Quizzes
- Philosophy Test Quizzes
- Practice Test Quizzes
- Pretest Quizzes
- Safety Test Quizzes
- Skill Assessment Quizzes
- Spelling Test Quizzes
- Standardized Test Quizzes
Back to top