Kuldeep 2 Team Ojas
.
- 1.
What is the condition for using a bent tube in the primary structure?
- A.
The support tube must have minimum dimensions of 1"x0.062"
- B.
The point which deviates farthest from a straight line connecting both ends MUST be supported.
- C.
The support tube must be angled at no more than 75 degrees from the plane of the bent tube.
- D.
Atleast 2 tubes must be attached to support it.
Correct Answer
B. The point which deviates farthest from a straight line connecting both ends MUST be supported.Explanation
The condition for using a bent tube in the primary structure is that the point which deviates farthest from a straight line connecting both ends must be supported.Rate this question:
-
- 2.
In the side view of the vehicle, the portion of the Main Roll Hoop that lies below the upper side impact member attachment point should be inclined to the vertical in the forward
- A.
20deg
- B.
30deg
- C.
10deg
- D.
ANY
Correct Answer
D. ANYExplanation
The correct answer is ANY because there is no specific requirement for the inclination angle of the portion of the Main Roll Hoop that lies below the upper side impact member attachment point in the side view of the vehicle. It can be inclined at any angle to the vertical depending on the design and structural requirements of the vehicle.Rate this question:
-
- 3.
Penalty for submitting SES a week after its due date is
- A.
50 points
- B.
60 points
- C.
70 points
- D.
No penalty
Correct Answer
A. 50 pointsExplanation
The penalty for submitting SES (presumably referring to a document or assignment) a week after its due date is 50 points. This implies that there is a penalty for late submission, and the penalty amount is 50 points.Rate this question:
-
- 4.
When the vehicles are approved for the dynamic events, which of the following modifications are not permitted to the vehicles
- A.
Substitution of suspension parts
- B.
Replacement of tires
- C.
Substitution of the head restraint
- D.
Adjustment of tire pressure
Correct Answer
A. Substitution of suspension partsExplanation
The question asks which modifications are not permitted to the vehicles when they are approved for the dynamic events. The correct answer is "Substitution of suspension parts." This means that the vehicles cannot have their suspension parts replaced with different ones. However, replacement of tires, substitution of the head restraint, and adjustment of tire pressure are allowed modifications.Rate this question:
-
- 5.
The drawings of the car included in the design report can be manual
- A.
True
- B.
False
Correct Answer
A. TrueExplanation
The explanation for the given correct answer is that the drawings of the car included in the design report can indeed be manual. This means that the drawings can be hand-drawn or created by using traditional artistic techniques, rather than being generated digitally or using computer-aided design (CAD) software. Manual drawings can provide a more artistic and personal touch to the design report, showcasing the creativity and skill of the designer.Rate this question:
-
- 6.
A capacitor with a capacitance of 100microFarad is currently charged to a voltage of 199.8V.How much additional energy is needed to charge it to a voltage of 301.4V and how longdoes it take?
- A.
The additional energy needed is 2.546J. The time needed is 3.4ms
- B.
The additional energy needed is 2.456J. The time needed is 2.9ms
- C.
The additional energy needed is 2.546J. The time needed can not be calculated with the given parameters.
- D.
The additional energy needed is 2.564J. The time needed is 3.2ms.
Correct Answer
C. The additional energy needed is 2.546J. The time needed can not be calculated with the given parameters. -
- 7.
Can a team have more than one captain ?
- A.
Yes
- B.
No
Correct Answer
A. YesExplanation
Yes, a team can have more than one captain. In certain situations, especially in sports or group activities, there may be multiple individuals who possess leadership qualities and can effectively guide the team. Having multiple captains can distribute the responsibility and workload, allowing for better coordination and decision-making within the team. It also promotes a sense of inclusivity and ensures that different perspectives and strengths are represented in the leadership role.Rate this question:
-
- 8.
A steady DC current is flowing through a coil with an inductance of 248mH. The storedenergy in the magnetic field is 431J. By how much does the current have to be increased, ifthe stored energy should be increased by 300J?
- A.
17.824A
- B.
17.825A
- C.
17.820A
- D.
17.822A
Correct Answer
A. 17.824AExplanation
The stored energy in the magnetic field of a coil is given by the equation E = 0.5 * L * I^2, where E is the energy, L is the inductance, and I is the current. We are given that the initial stored energy is 431J and the inductance is 248mH. We can rearrange the equation to solve for the initial current: I = sqrt(2E / L). Substituting the given values, we find the initial current to be approximately 17.825A. To increase the stored energy by 300J, we can use the same equation and solve for the final current: I = sqrt(2(E + 300) / L). Substituting the values, we find the final current to be approximately 17.824A.Rate this question:
-
- 9.
Which measurement voltage will be used during the insulation measurement test for a carwith a maximum tractive system voltage of 260V?
- A.
250V
- B.
260V
- C.
125V
- D.
500V
Correct Answer
D. 500VExplanation
During the insulation measurement test for a car with a maximum tractive system voltage of 260V, a measurement voltage of 500V will be used. This higher voltage is necessary to ensure that the insulation can withstand the maximum voltage of the car's tractive system. Using a lower voltage, such as 250V or 125V, may not provide an accurate assessment of the insulation's ability to handle the higher voltage. Therefore, a measurement voltage of 500V is required for this test.Rate this question:
-
- 10.
How many max. Members are allowed in the driver change area for an EV?
- A.
4 excluding the driver
- B.
3 including the one driver.
- C.
3 including 2 drivers and ESO.
- D.
4 including 1 driver and ESO.
Correct Answer
C. 3 including 2 drivers and ESO.Explanation
The correct answer is 3 including 2 drivers and ESO. This means that in the driver change area for an EV, a maximum of 3 people are allowed, which includes 2 drivers and an ESO (Electric Safety Officer). The ESO is responsible for ensuring the safety of the electric vehicle during the driver change process.Rate this question:
-
- 11.
Points deducted for a missing material in BOM?
- A.
5
- B.
4
- C.
3
- D.
2
- E.
1
Correct Answer
E. 1Explanation
The given answer suggests that 1 point is deducted for a missing material in the Bill of Materials (BOM). This means that if a required material is not included in the BOM, a penalty of 1 point will be imposed. This deduction could be a way to incentivize accuracy and thoroughness in creating and maintaining the BOM, ensuring that all necessary materials are accounted for and reducing the risk of production delays or errors.Rate this question:
-
- 12.
Minimum area moment of inertia of Side impact structure, front bulkhead, roll hoop bracing,driver’s restraint harness attachment is—
- A.
8590mm^4
- B.
8509mm^4
- C.
6695mm^4
- D.
6694mm^4
Correct Answer
C. 6695mm^4Explanation
The minimum area moment of inertia of the side impact structure, front bulkhead, roll hoop bracing, and driver's restraint harness attachment is 6695mm^4. This value represents the resistance of the structure to bending and torsion forces, with a higher value indicating a stronger and more rigid structure. Therefore, the correct answer is 6695mm^4.Rate this question:
-
- 13.
One layer of firewall, facing the tractive system side, must be made of aluminum with athickness of at least _____. This part of the tractive system firewall must be grounded according to ______.(fill the correct option in the statement)
- A.
0.5mm, EV 4.3
- B.
1 mm, EV4.5
- C.
1.2 mm, EV 4.3
- D.
1.5 mm, EV 5.0
Correct Answer
A. 0.5mm, EV 4.3Explanation
The correct answer is 0.5mm, EV 4.3. According to the given information, one layer of the firewall facing the tractive system side must be made of aluminum with a thickness of at least 0.5mm. Additionally, this part of the tractive system firewall must be grounded according to EV 4.3.Rate this question:
-
- 14.
Total energy absorbed by the impact attenuator must meet or exceed:
- A.
7050J
- B.
7450J
- C.
7150J
- D.
7350J
Correct Answer
D. 7350JExplanation
The total energy absorbed by the impact attenuator must meet or exceed 7350J. This means that the impact attenuator must be able to absorb at least 7350J of energy in order to effectively attenuate the impact. If the impact attenuator can absorb less than 7350J, it would not be able to adequately protect against the impact forces.Rate this question:
-
- 15.
"Pull into penalty box for discussion with Marshal" is repreented by which flag?
- A.
Black with orange dot
- B.
Black
- C.
Red
- D.
Blue
Correct Answer
B. BlackExplanation
The flag that represents "Pull into penalty box for discussion with Marshal" is black.Rate this question:
-
- 16.
All equivalency calculations must prove equivalency related to steel grade:
- A.
SAE/AISI 1011
- B.
SAE/AISI 1010
- C.
SAE/AISI 1011
- D.
SAE/AISI 1020
Correct Answer
B. SAE/AISI 1010Explanation
The correct answer is SAE/AISI 1010 because it is the only steel grade mentioned in the options that is not repeated. The other steel grades, SAE/AISI 1011 and SAE/AISI 1020, are mentioned twice, indicating that they are not unique options. Therefore, SAE/AISI 1010 is the only steel grade that satisfies the requirement for equivalency calculations.Rate this question:
-
- 17.
In upright and reclined driving positions, what angles must the lap belts be at, with the horizontal?
- A.
40-60 and 60-80 degrees
- B.
45-60 and 60-80 degrees
- C.
45-65 and 65-80 degrees
- D.
45-65 and 60-80 degrees
Correct Answer
D. 45-65 and 60-80 degreesExplanation
In both the upright and reclined driving positions, the lap belts must be at angles between 45-65 degrees and 60-80 degrees with the horizontal.Rate this question:
-
- 18.
What is the standard for "Motor vehicle brake fluid"?
- A.
J1703
- B.
J2053
- C.
J2045
- D.
J175
Correct Answer
A. J1703Explanation
J1703 is the correct answer because it is the standard for "Motor vehicle brake fluid." This standard is set by the Society of Automotive Engineers (SAE) and specifies the requirements and performance characteristics for brake fluids used in motor vehicles. Brake fluid plays a crucial role in the braking system by transferring force from the brake pedal to the brakes, so it is important to use a fluid that meets the necessary standards for safety and performance.Rate this question:
-
Quiz Review Timeline +
Our quizzes are rigorously reviewed, monitored and continuously updated by our expert board to maintain accuracy, relevance, and timeliness.
-
Current Version
-
Mar 21, 2023Quiz Edited by
ProProfs Editorial Team -
Jan 15, 2017Quiz Created by
Akshaydua
Back to top