Ikr 18 Pre-virtual Round Online Test Paper (Set A)
-
The ergonomically best angle between Thighs and Legs when the driver is in driving position?
-
110
-
180
-
135
-
100
-
Instructions: This is a multiple choice test of 50 questions. Read all the questions carefully. Each question carries 2 marks. There is no negative marking. Maximum time allotted to answer all the questions is 30 minutes. Submit this test before time out.
- 2.
Roll hoop should be made from?
-
Glass fiber material using a mold
-
Single pipe bended using different bending techniques
-
By welding different pipes to form a single structure
-
By casting it using iron or aluminium
Correct Answer
A. Single pipe bended using different bending techniquesExplanation
The roll hoop should be made from a single pipe that is bent using different bending techniques. This ensures that the roll hoop is strong and able to withstand the forces and impacts it may encounter. Using a single pipe also provides a seamless and continuous structure, reducing the risk of weak points or potential failure.Rate this question:
-
- 3.
Minimum wheelbase of Go-kart must be?
-
41 Inch
-
45 Inch
-
48 Inch
-
51 Inch
Correct Answer
A. 41 InchExplanation
The minimum wheelbase of a go-kart must be 41 inches. This measurement refers to the distance between the center of the front axle and the center of the rear axle. A shorter wheelbase provides better maneuverability and agility, making it easier for the go-kart to navigate tight corners and turns. It also improves stability and control, allowing the driver to maintain better balance while driving. Therefore, a minimum wheelbase of 41 inches is necessary to ensure optimal performance and handling of the go-kart.Rate this question:
-
- 4.
Maximum engine capacity provided is?
-
150 cc
-
200 cc
-
127 cc
-
100 cc
Correct Answer
A. 150 ccExplanation
The maximum engine capacity provided is 150 cc. This means that the largest engine capacity available among the options is 150 cc.Rate this question:
-
- 5.
The sidewalls of the Spillover tank should be at least ________ inches in height.
-
4 inch
-
3 inch
-
5 inch
-
3.5 inch
Correct Answer
A. 3 inchExplanation
The sidewalls of the Spillover tank should be at least 3 inches in height to ensure that it can effectively contain and control the overflow of liquid. This height is necessary to prevent any spillage or leakage that could occur if the walls were shorter. Additionally, a minimum height of 3 inches provides a sufficient buffer to handle any fluctuations in the liquid level within the tank.Rate this question:
-
- 6.
The function of a kill switch is to?
-
Turn off all the electrical and electronic connections of a Go-kart
-
Turn off the electrical application related to power source like batteries, Motors, Motor controller etc.
-
Turn off electronic part of Go-kart like ECU of Go-kart
-
Turn off all the electric connections expect brake light, side indicators (if used)
Correct Answer
A. Turn off all the electric connections expect brake light, side indicators (if used)Explanation
A kill switch is used to deactivate or shut down a system or device. In the context of a go-kart, the purpose of a kill switch is to turn off all the electric connections except for the brake light and side indicators (if used). This ensures that all electrical and electronic components of the go-kart are deactivated, except for the necessary safety lights. This allows for a quick and safe shutdown of the go-kart in case of an emergency or when it needs to be turned off.Rate this question:
-
- 7.
Teams are required to provide FILA report of ergonomics according to SAE _______percentile male and SAE _____percentile female
-
90th and 5th
-
85th and 10th
-
95th and 5th
-
90th and 10th
Correct Answer
A. 95th and 5thExplanation
Teams are required to provide a FILA report of ergonomics according to SAE 95th percentile male and SAE 5th percentile female. This means that the ergonomics report should include data and analysis based on the body dimensions and characteristics of individuals who represent the 95th percentile of male population and the 5th percentile of female population. This ensures that the design and layout of the product or system takes into account the needs and comfort of a wide range of users, including those who may have larger or smaller body sizes and proportions.Rate this question:
-
- 8.
Fire Extinguisher should be mounted on?
-
Near the Driver foot
-
On ground floor above the chassis
-
Firewall near the driver compartment
-
At the rear end of the chassis
Correct Answer
A. Firewall near the driver compartmentExplanation
The correct answer is "Firewall near the driver compartment." A firewall is a barrier designed to prevent the spread of fire and smoke between different compartments of a vehicle. By mounting the fire extinguisher near the driver compartment's firewall, it ensures quick and easy access in case of a fire emergency. Placing it in this location also helps to minimize the risk of the fire spreading to other parts of the vehicle, protecting both the driver and the vehicle itself.Rate this question:
-
- 9.
The background colour of sticker number must be of?
-
Yellow
-
Blue
-
Red
-
White
Correct Answer
A. YellowExplanation
The background color of the sticker number must be yellow. This implies that the sticker number should have a yellow background color, as opposed to blue, red, or white.Rate this question:
-
- 10.
Query submission will be submitted at _______________ mail ID?
Rate this question:
- 11.
Pedal actuation should be done by?
-
Foot
-
Hand
-
Combination of both Foot and Hand
-
Actuation should be mobile operated
Correct Answer
A. FootExplanation
Pedal actuation should be done by the foot because it allows for better control and stability. Using the foot to operate pedals is a common practice in various activities such as driving a car, riding a bicycle, or playing certain musical instruments like the piano or organ. The foot provides a larger surface area and stronger muscles, making it more suitable for tasks that require precision and strength. Additionally, using the foot for pedal actuation allows the hands to remain free for other tasks, enhancing overall efficiency and multitasking abilities.Rate this question:
-
- 12.
Minimum Ground Clearance should be?
-
1 Inch
-
2 Inch
-
3 Inch
-
4 Inch
Correct Answer
A. 1 InchExplanation
The minimum ground clearance should be 1 inch. Ground clearance refers to the distance between the lowest point of a vehicle and the ground. A higher ground clearance is generally preferred for off-road vehicles or in areas with rough terrain, but a minimum ground clearance of 1 inch is necessary to prevent the vehicle from scraping or getting damaged by obstacles on the road.Rate this question:
-
- 13.
Maximum turning radius of the Go- kart allowed is?
-
1 Mtrs
-
2 Mtrs
-
3 Mtrs
-
4 Mtrs
Correct Answer
A. 3 MtrsExplanation
The maximum turning radius of the Go-kart allowed is 3 meters. This means that the Go-kart is able to make a turn within a radius of 3 meters without any issues or limitations. A larger turning radius would limit the maneuverability of the Go-kart, while a smaller turning radius would allow for sharper and tighter turns. Therefore, a turning radius of 3 meters strikes a balance between maneuverability and stability.Rate this question:
-
- 14.
Trusses/bracers for roll hoop should be minimum of ________inches from lower of frame?
-
9
-
5
-
15
-
12
Correct Answer
A. 15Explanation
The trusses/bracers for the roll hoop should be a minimum of 15 inches from the lower part of the frame. This distance is necessary to ensure that the trusses/bracers provide sufficient support and stability to the roll hoop, preventing it from collapsing or bending during impact or rollover situations. A greater distance helps to distribute the load more effectively and enhances the overall structural integrity of the roll hoop.Rate this question:
-
- 15.
Jack point should be painted in?
-
Yellow colour
-
Red colour
-
Black colour
-
Orange colour
Correct Answer
A. Orange colourExplanation
The jack point should be painted in orange color because it is a universal standard color for indicating the location of a jack point on a vehicle. This color helps to easily identify the specific area where the jack should be placed to safely lift the vehicle. Using orange color ensures that the jack point is clearly visible and prevents any confusion or potential damage to the vehicle.Rate this question:
-
- 16.
FMSCI is recognized by?
-
Ministry of Youth Affairs
-
Ministry of New and Renewable Energy
-
Ministry of Micro, Small & Medium Enterprises
-
Start Up India
Correct Answer
A. Ministry of Youth AffairsExplanation
FMSCI (Federation of Motor Sports Clubs of India) is recognized by the Ministry of Youth Affairs. This recognition signifies that FMSCI is officially acknowledged and supported by the government department responsible for youth affairs in India. This recognition highlights the importance of FMSCI's work in promoting and regulating motor sports activities in the country, particularly among the youth population.Rate this question:
-
- 17.
____________permits usage of safety equipment’s in ISIE INDIA events?
-
Ministry of Micro, Small & Medium Enterprises
-
Ministry of New and Renewable Energy
-
SFI foundation INC
-
Ministry of Youth Affairs
Correct Answer
A. SFI foundation INCExplanation
The SFI (Specialty Equipment Market Association) foundation INC permits the usage of safety equipment in ISIE INDIA events. This organization is known for its involvement in promoting safety standards and regulations in the automotive industry. They provide certifications and guidelines for various safety equipment used in motorsports and other automotive events. Therefore, it is logical to conclude that the SFI foundation INC would be responsible for permitting the usage of safety equipment in ISIE INDIA events.Rate this question:
-
- 18.
For kart eligibility, teams are required to submit a manufacturing video of Minimum?
-
3 Minutes
-
4 Minutes
-
5 Minutes
-
4 and Half Minutes
Correct Answer
A. 5 MinutesExplanation
Teams are required to submit a manufacturing video of at least 5 minutes in length to be eligible for kart eligibility. This video should showcase the manufacturing process of the kart and provide sufficient details and evidence of the team's work. A longer video allows for a more comprehensive demonstration of the manufacturing process, ensuring that teams have provided enough information to meet the eligibility requirements.Rate this question:
-
- 19.
Dimension for rear dry(slick) tire is?
-
4.5*10.0-5
-
5*10.0-5
-
7.1*11.0-5
-
6.0*11.0-5
Correct Answer
A. 7.1*11.0-5Explanation
The dimension for the rear dry (slick) tire is 7.1*11.0-5.Rate this question:
-
- 20.
Chassis should be made from?
-
Circular section of minimum 1.2 mm wall thickness
-
Rectangular section of minimum 1.2 mm wall thickness
-
Circular section of minimum 2 mm wall thickness
-
Rectangular section of minimum 2 mm wall thickness
Correct Answer
A. Circular section of minimum 1.2 mm wall thicknessExplanation
The chassis should be made from a circular section of minimum 1.2 mm wall thickness. This is because a circular section provides better structural integrity and stability compared to a rectangular section. Additionally, a minimum wall thickness of 1.2 mm ensures that the chassis is strong and durable enough to withstand the required load and stress.Rate this question:
-
- 21.
Maximum number of attempts provided for T.I and Brake test?
-
1
-
2
-
3
-
4
Correct Answer
A. 2Explanation
The maximum number of attempts provided for the T.I and Brake test is 2.Rate this question:
-
- 22.
Jack point must be mounted______
-
Below the main frame
-
Above the main frame
-
Below the Bumper
-
Above the Bumper
Correct Answer
A. Below the main frameExplanation
The correct answer is "Below the main frame" because the jack point is a specific location on a vehicle where a jack can safely lift the vehicle. Mounting the jack point below the main frame ensures that the weight of the vehicle is evenly distributed and the lifting process is stable and secure. Placing it above the main frame or below/above the bumper may not provide the necessary support and could potentially damage the vehicle.Rate this question:
-
- 23.
Dimensions of the jack points are (all units provided are in Inches)?
-
12*2*0.1968
-
10*1*0.1968
-
10*2*0.1968
-
12*1*0.1968
Correct Answer
A. 12*2*0.1968Explanation
The dimensions of the jack points are given as 12*2*0.1968 inches. This means that the length of the jack point is 12 inches, the width is 2 inches, and the height is 0.1968 inches.Rate this question:
-
- 24.
Hitch point should be painted in?
-
Orange
-
Red
-
Yellow
-
Black
Correct Answer
A. YellowExplanation
The hitch point should be painted in yellow. This is because yellow is a universally recognized color for caution or warning. Painting the hitch point in yellow helps to draw attention to it and indicates that caution should be exercised when using or approaching the hitch point. This can help prevent accidents or mishaps and ensure the safety of individuals using the hitch point.Rate this question:
-
- 25.
Q: Number of students allowed for Virtual round presentation?
-
Min of 3
-
Max of 5
-
Min of 7
-
Max of 2
Correct Answer
A. Max of 5Explanation
The correct answer is "Max of 5" because it indicates the maximum number of students that are allowed for the virtual round presentation. This means that the presentation can have a maximum of 5 students participating.Rate this question:
-
- 26.
Minimum field of vision when the driver is in driving position?
-
180
-
200
-
150
-
210
Correct Answer
A. 200Explanation
The minimum field of vision when the driver is in the driving position is 200. This means that the driver should be able to see at least 200 degrees of their surroundings without any obstructions. Having a wide field of vision is important for safe driving as it allows the driver to be aware of any potential hazards or obstacles on the road. A larger field of vision enables the driver to have better situational awareness and react promptly to any unexpected situations.Rate this question:
-
- 27.
Minimum surface thickness for the material used in the firewall?
-
1.5 mm
-
2 mm
-
2.5 mm
-
3 mm
Correct Answer
A. 1.5 mmExplanation
The minimum surface thickness for the material used in the firewall is 1.5 mm. This means that the material must have a thickness of at least 1.5 mm in order to be suitable for use in the firewall. A thinner material may not provide enough strength and protection, while a thicker material may be unnecessary and add unnecessary weight to the firewall. Therefore, 1.5 mm is the optimal thickness for the material used in the firewall.Rate this question:
-
- 28.
Allowed steering play?
-
5 degrees
-
6 degrees
-
7 degrees
-
8 degrees
Correct Answer
A. 7 degreesExplanation
The allowed steering play is 7 degrees. Steering play refers to the amount of movement in the steering wheel before it actually starts to turn the wheels. In this case, 7 degrees is the maximum amount of play that is considered acceptable. This means that the steering wheel can be turned up to 7 degrees without any response from the wheels. Any play beyond this limit would indicate a potential issue with the steering system and may require adjustment or repair.Rate this question:
-
- 29.
Maximum weight of the vehicle should not exceed________Kg
-
130 Kg
-
125 Kg
-
180 Kg
-
220 kg
Correct Answer
A. 130 KgExplanation
The maximum weight of the vehicle should not exceed 130 Kg. This means that the vehicle should not weigh more than 130 Kg in order to comply with the given requirement.Rate this question:
-
- 30.
The colour code of yellow flag determines?
-
Stop the vehicle immediately
-
Pull into designation passing zone
-
Pull into penalty box for discussion
-
Danger, slow down your vehicle
Correct Answer
A. Danger, slow down your vehicleExplanation
The yellow flag is used in various sports and racing events to indicate danger or caution. In the context of this question, the colour code of the yellow flag determines that there is a potential danger ahead and drivers should slow down their vehicles to ensure safety. It serves as a warning signal for drivers to be cautious and prepared for any potential hazards on the road.Rate this question:
-
- 31.
Driver suit must be minimum of_________ layers?
-
1 layer
-
2 layers
-
3 layers
-
4 layers
Correct Answer
A. 1 layerExplanation
The correct answer is 1 layer because a driver suit must have at least one layer to provide some level of protection against fire and heat. Multiple layers can provide additional safety, but the minimum requirement is one layer.Rate this question:
-
- 32.
Bumpers should be at?
-
Front side of the Go-kart only
-
Rear side of the Go-kart only
-
Front & Rear side of Go-kart
-
Front, side & rear side of Go-kart
Correct Answer
A. Front & Rear side of Go-kartExplanation
Bumpers should be placed on the front and rear sides of a go-kart. This is because bumpers are designed to absorb impact and protect the vehicle and its occupants in the event of a collision. By having bumpers on both the front and rear, the go-kart is better equipped to withstand impacts from multiple directions and minimize damage. Additionally, having bumpers on both ends improves the overall safety of the go-kart by reducing the risk of injury to the driver and passengers.Rate this question:
-
- 33.
Scatter shield must be rigidly mounted on?
-
All the four tyres
-
Underneath of driver’s compartment
-
On master cylinder of brake system
-
All the rotating part in transmission system
Correct Answer
A. All the rotating part in transmission systemExplanation
The scatter shield must be rigidly mounted on all the rotating parts in the transmission system. This is because the scatter shield is a protective device designed to contain and prevent the scattering of debris in the event of a transmission failure. By mounting it on all the rotating parts, it ensures that any debris generated during a failure will be contained within the shield, minimizing the risk of injury or damage to other components.Rate this question:
-
- 34.
Which of the following kind of steering wheel material is not allowed?
-
Cast iron
-
AISI 1020
-
Carbon fibre
-
Aluminium
Correct Answer
A. Carbon fibreExplanation
Carbon fibre is not allowed as a steering wheel material because it is not strong enough to withstand the forces and impacts experienced during steering. Carbon fibre is a lightweight material used in aerospace and sports industries for its high strength-to-weight ratio, but it is not suitable for steering wheels in vehicles due to its limited durability and potential for failure under stress.Rate this question:
-
- 35.
Maximum Ground clearance allowed?
-
1 Inch
-
2 Inches
-
3 Inches
-
4 Inches
Correct Answer
A. 2 InchesExplanation
The maximum ground clearance allowed is 2 inches. This means that any vehicle or object should not exceed a height of 2 inches from the ground. This restriction is likely in place to ensure that vehicles or objects do not pose a risk or obstruction to other vehicles or pedestrians. It also helps to maintain smooth traffic flow and prevent any potential accidents or damage to the road or infrastructure.Rate this question:
-
- 36.
Font colour of sticker number must be of?
-
Black
-
Purple
-
Dark brown
-
Green
Correct Answer
A. BlackExplanation
The font colour of the sticker number must be black because it provides the highest contrast against most background colours, ensuring that the number is easily visible and readable. This is particularly important for stickers that need to be easily identified or for situations where quick recognition is necessary.Rate this question:
-
- 37.
A minimum of ______ mm hole should be provided on chassis for wall thickness inspection during technical inspection?
-
1mm
-
2mm
-
3mm
-
4mm
Correct Answer
A. 3mmExplanation
A minimum of 3mm hole should be provided on the chassis for wall thickness inspection during technical inspection. This is because a larger hole would allow for better visibility and measurement of the wall thickness, ensuring that it meets the required standards. Smaller holes may not provide enough space for accurate inspection, while larger holes may weaken the chassis structure. Therefore, a 3mm hole strikes a balance between visibility and maintaining the integrity of the chassis.Rate this question:
-
- 38.
In chassis material, in case of steel minimum carbon percentage should be
-
0.01%
-
0.1%
-
0.03%
-
0.3%
Correct Answer
A. 0.1%Explanation
Steel is an alloy of iron and carbon, and the percentage of carbon in the steel determines its strength and hardness. A minimum carbon percentage of 0.1% is required in the chassis material to ensure sufficient strength and durability. A lower carbon percentage would result in weaker steel, which may not be able to withstand the stresses and loads experienced by a chassis in a vehicle. Therefore, 0.1% is the correct answer.Rate this question:
-
- 39.
Gap between tire and bumper must be at least
-
3 inches
-
2 inches
-
2.5 inches
-
4 inches
Correct Answer
A. 3 inchesExplanation
The gap between the tire and bumper must be at least 3 inches in order to ensure proper clearance and prevent any potential contact or damage between the two. This allows for enough space for the tire to rotate freely without rubbing against the bumper, reducing the risk of wear and tear on both components. Additionally, a larger gap may be necessary for off-road or larger tires to accommodate their size and movement.Rate this question:
-
- 40.
For team number stickers diameter should be
-
4 inches
-
5 inches
-
6 inches
-
7 inches
Correct Answer
A. 6 inchesExplanation
The correct answer is 6 inches. This is the appropriate diameter for team number stickers.Rate this question:
-
- 41.
In case of full circle steering wheel outer diameter should be
-
8 inches
-
10 inches
-
12 inches
-
14 inches
Correct Answer
A. 10 inchesExplanation
In the case of a full circle steering wheel, the outer diameter should be 10 inches. This size allows for a comfortable grip and provides enough surface area for the driver to have full control and maneuverability of the steering wheel. It strikes a balance between being too small, which could make it difficult to handle, and being too large, which could be cumbersome and make it harder to make precise movements while driving.Rate this question:
-
- 42.
The brakes must be able to act on
-
Only one front wheels
-
Only one rear wheel
-
Both rear wheels
-
Both front wheels
Correct Answer
A. Both rear wheelsExplanation
The correct answer is "Both rear wheels" because in a typical vehicle, the braking system is designed to distribute braking force evenly between the front and rear wheels. This helps to ensure stability and efficient braking. By applying the brakes to both rear wheels, the vehicle can effectively slow down or stop without causing skidding or loss of control.Rate this question:
-
- 43.
The brake light itself must be
-
Near round shape
-
Square
-
Triangle
-
Rectangle
Correct Answer
A. Near round shapeExplanation
The brake light must be near round shape because it helps to provide maximum visibility from different angles. A round shape allows the light to be evenly distributed, ensuring that it can be seen from both the rear and sides of the vehicle. This shape also helps to minimize blind spots and increases safety on the road.Rate this question:
-
- 44.
Engine can be placed at
-
Either left or right side of driver
-
Back side of driver
-
Either a or b
-
Neither a nor b
Correct Answer
A. Back side of driverExplanation
The engine can be placed at the back side of the driver. This placement is commonly seen in rear-engine vehicles where the engine is located behind the driver's seat. This configuration allows for better weight distribution and traction, as the weight of the engine is positioned over the rear wheels. Additionally, having the engine at the back can also free up space in the front of the vehicle for other components or storage.Rate this question:
-
- 45.
The transmission to be used in the Go-Karts must be of
-
Rear wheel drive only
-
Front wheel drive only
-
Can be rear or front wheel drive
-
None of the above
Correct Answer
A. Rear wheel drive onlyExplanation
The transmission to be used in the Go-Karts must be of rear wheel drive only because rear wheel drive provides better traction and stability, especially when accelerating out of corners. It also allows for better weight distribution, as the engine is located in the rear, resulting in improved handling and control. Additionally, rear wheel drive is more suitable for racing applications as it allows for better power delivery and control over the vehicle.Rate this question:
-
- 46.
The bumper should be at least _______ inch from the ground?
-
4
-
5
-
2
-
1
Correct Answer
A. 5Explanation
The correct answer is 5 because the question is asking for the minimum distance the bumper should be from the ground. A higher distance ensures that the bumper will not scrape against the ground or obstacles, providing better protection for the vehicle.Rate this question:
-
- 47.
Minimum distance between firewall and driver seat?
-
2 inch
-
3 inch
-
4 inch
-
2.5 inch
Correct Answer
A. 3 inchExplanation
The minimum distance between the firewall and the driver seat is 3 inches. This is important for safety reasons as it allows for enough space to protect the driver in case of a collision or accident. A larger distance provides a buffer zone and reduces the risk of injury from impact or heat transfer from the engine compartment. A smaller distance may not provide adequate protection and can increase the chances of injury. Therefore, a minimum distance of 3 inches is recommended.Rate this question:
-
- 48.
The foot point of the occupant must be______
-
Above the H- point
-
Below the H- point
-
Above C.G
-
Below C.G
Correct Answer
A. Below the H- pointExplanation
The correct answer is "Below the H-point." The H-point refers to the hip point, which is the location of the occupant's hips when seated in a vehicle. Placing the foot point below the H-point ensures proper ergonomics and comfort for the occupant. This positioning allows for a natural and relaxed seating posture, with the feet resting comfortably on the floor. It also helps in maintaining stability and balance while seated, contributing to overall safety and comfort during the ride.Rate this question:
-
- 49.
All the fasteners used for major mounting should be of?
-
Flange
-
Slotted
-
Lock Nut
-
Heavy Hex type
Correct Answer
A. Lock NutExplanation
The correct answer is "Lock Nut" because fasteners used for major mounting need to provide a secure and reliable connection. Lock nuts have a special design that includes a nylon insert or a metal ring, which helps prevent the nut from loosening due to vibrations or other external forces. This ensures that the fastener remains tightly secured, reducing the risk of accidents or damage. Therefore, lock nuts are the most suitable type of fastener for major mounting applications.Rate this question:
-
Quiz Review Timeline (Updated): Mar 21, 2023 +
Our quizzes are rigorously reviewed, monitored and continuously updated by our expert board to maintain accuracy, relevance, and timeliness.
-
Current Version
-
Mar 21, 2023Quiz Edited by
ProProfs Editorial Team -
Feb 24, 2018Quiz Created by
Indian Karting
- Aptitude Test Quizzes
- Course Test Quizzes
- Driving Test Quizzes
- English Test Quizzes
- FCAT Quizzes
- General Knowledge Quizzes
- Intelligence Test Quizzes
- Medical Test Quizzes
- Mock Test Quizzes
- Philosophy Test Quizzes
- Practice Test Quizzes
- Pretest Quizzes
- Safety Test Quizzes
- Skill Assessment Quizzes
- Spelling Test Quizzes
- Standardized Test Quizzes
Back to top