Geetansh And Lakshya 1

After a TI (Technical Inspection), adjustments of sensors cannot be modified or repaired. This is because sensors are typically calibrated and adjusted during the inspection process to ensure accurate readings and performance. Once the inspection is complete, any further adjustments to the sensors may compromise their accuracy and functionality. Therefore, it is important to ensure that all necessary adjustments are made before the TI.

The maximum deflection of the aerodynamic device can be determined by calculating the maximum deflection under the given force using the formula for deflection of a beam. The formula is δ = (F * L^3) / (48 * E * I), where δ is the deflection, F is the force, L is the length, E is the modulus of elasticity, and I is the moment of inertia. Since the dimensions are given as 45x5 cm, we can assume it is a rectangular beam. The moment of inertia for a rectangular beam is (b * h^3) / 12. Plugging in the values and solving, we find that the maximum deflection is 8mm. Therefore, the correct answer is both a & b.

Team 4 was not able to register because its registration time was after the deadline of 30-01-2017 6:30 pm.

The team initially registered 35 participants on time, which would require a certain registration fee. However, they later decided to add 10 more participants after the deadline had passed. This means that the additional 10 participants would not be able to register and pay the registration fee. Therefore, the total registration fee the whole team needs to pay would be the initial fee for the 35 participants. Hence, the correct answer is 1550 euros.

The team will be sent back to the pit and asked to remove the play and decrease it to less than 6 degrees because the given scenario states that when the driver turns the steering wheel, the rear wheel steering system moves 6.5 degrees but none of the wheels turn right or left. This indicates that there is excessive play in the system, which needs to be eliminated for proper functioning. Therefore, the team will be required to fix this issue by reducing the play to less than 6 degrees.

The team can remove the rear bulkhead in order to reduce the chassis weight.

The correct answer is 1.2mm because the wall thickness of the member is directly related to the area moment of inertia. A larger area moment of inertia indicates a stronger member, which allows for a thinner wall thickness. Therefore, with an area moment of inertia of 8509mm^4, a wall thickness of 1.2mm would be sufficient.

The only exception that can be made for a fixture which supports the entire sample when the sample is clamped to the fixture is a 32mm hole aligned co-axially with the punch.

The red and yellow striped flag is used to indicate that the track is slippery or that there is something on the surface that should not be there. This flag is commonly used in motorsports to warn drivers of hazardous conditions on the track. The red and yellow stripes serve as a visual signal to alert drivers to adjust their driving and proceed with caution.

If Team A finished the endurance without any Did Not Finish (DNF), they will be awarded the maximum points available, which is 25. This indicates that they successfully completed the endurance event without any issues or penalties.

The Skidpad procedure involves several factors. Firstly, teams on their first run are given priority. Secondly, the starting order is determined by the team's arrival time at the skidpad event. Thirdly, a green flag is used to indicate that the driver can begin. Fourthly, the vehicle enters the skidpad perpendicular to the figure of eight and completes one full lap on the right circle to establish the turn. Finally, after finishing the fourth lap, the vehicle exits the track perpendicular to the figure of eight and in the same direction as it entered. Therefore, all of the given statements are true about the Skidpad procedure.

not-available-via-ai

The cars that are CV cars are B and C. This is because they are the only options given that are specified as CV cars. The other options, 200, 269, and 400, do not have any indication that they are CV cars. Therefore, the correct answer is B & C.

All of the options listed (personal address, clothing size, emergency contact person and phone, valid health insurance certificate for Germany) are mandatory to be filled in as personal information by a team member.

The procedure for raising a protest includes filing it in writing and submitting it to the officials by the team captain. Any queries must be brought to the officials' attention for a preliminary review before a protest can be filed. Additionally, a team must post a 20 point protest bond, which will be forfeited if their protest is rejected. However, the decision of the officials regarding any protest can be in a written/oral form and is final. Therefore, the incorrect statements are C & D.