Upsm Hs Trimester 2 Break
Type in your name (full name, no nicknames) into the box below. Answer all the questions to the best of your ability. Print off (or save as pdf) your certificate of completion. Your certificate will be turned in first thing when you return from break and will be worth 100 points.
Questions and Answers
- 1.
What are the three multiviews?
- A.
Right, Top, Front
- B.
Front, Left, Top
- C.
Top, Bottom, Right
- D.
Right, Left, Top
Correct Answer
A. Right, Top, FrontExplanation
The three multiviews commonly used in technical drawing and engineering are right, top, and front views. These views allow for a comprehensive representation of an object from different perspectives. The right view shows the object as seen from the right side, the top view shows the object from above, and the front view shows the object as seen from the front. By combining these three views, a complete understanding of the object's shape and dimensions can be achieved.Rate this question:
-
- 2.
Which of the following is NOT part of our line conventions?
- A.
Center lines
- B.
Construction lines
- C.
Intermediate lines
- D.
Dimension lines
Correct Answer
C. Intermediate linesExplanation
Intermediate lines are not part of line conventions. Line conventions typically include center lines, construction lines, and dimension lines, which are used to represent different features or dimensions in technical drawings. Intermediate lines, on the other hand, are not commonly used in line conventions and may refer to any additional lines that are not specifically defined in the context of the question.Rate this question:
-
- 3.
True or False: You can sometimes dimension the isometric view in your Inventor drawings.
- A.
True
- B.
False
Correct Answer
B. FalseExplanation
In Inventor drawings, the isometric view is a three-dimensional representation of an object. However, dimensions in isometric views are not accurate because they are distorted due to the perspective. Therefore, it is not possible to dimension the isometric view accurately in Inventor drawings.Rate this question:
-
- 4.
Which multiviews give you the depth of an object?
- A.
Right and Front
- B.
Top and Right
- C.
Left and Front
- D.
Top and Front
Correct Answer
B. Top and RightExplanation
The combination of top and right multiviews gives you the depth of an object. By viewing the object from the top, you can determine its height or thickness, while viewing it from the right side allows you to perceive its width or breadth. Together, these two perspectives provide a comprehensive understanding of the object's three-dimensional shape and depth.Rate this question:
-
- 5.
True or False: Something that has never been thought of is an innovation.
- A.
True
- B.
False
Correct Answer
B. FalseExplanation
The statement "Something that has never been thought of is an innovation" is false. Innovation refers to the creation or introduction of something new or different that brings about a positive change or improvement. It involves the application of new ideas, methods, or technologies to solve a problem or meet a need. Therefore, for something to be considered an innovation, it must be a novel and inventive concept that goes beyond what has been previously thought of or done.Rate this question:
-
- 6.
When dimensioning a hole in an engineering drawing you should do which of the following?
- A.
Place a center mark
- B.
Dimension the diameter or radius
- C.
Dimension the location of the hole with two annotations
- D.
All of the above
Correct Answer
D. All of the aboveExplanation
When dimensioning a hole in an engineering drawing, it is important to include all of the options mentioned. Placing a center mark helps indicate the exact location of the hole. Dimensioning the diameter or radius provides information about the size of the hole. Lastly, dimensioning the location of the hole with two annotations ensures that the position of the hole is accurately communicated. By following all of these steps, the drawing can effectively communicate the necessary information for manufacturing or assembly.Rate this question:
-
- 7.
What does the word annotate mean?
- A.
Listen
- B.
Make a current invention better
- C.
Make a 2D object 3D
- D.
Dimension/describe an object
Correct Answer
D. Dimension/describe an objectExplanation
The word "annotate" means to dimension or describe an object. It involves adding notes, comments, or explanations to provide additional information or context about the object. This could include labeling specific parts, indicating measurements or dimensions, or providing detailed descriptions of the object's characteristics or features.Rate this question:
-
- 8.
What does eclectic mean?
- A.
Difficult
- B.
Various
- C.
Solid
- D.
Hard Work
Correct Answer
B. VariousExplanation
Eclectic means having a variety of different styles, ideas, or sources. It implies a diverse or wide-ranging selection or approach. Therefore, the word "various" accurately represents the meaning of eclectic.Rate this question:
-
- 9.
In order to make a sketch in Inventor you must first have what?
- A.
An extrusion
- B.
A plane
- C.
A line
- D.
A rectangle
Correct Answer
B. A planeExplanation
To make a sketch in Inventor, a plane is required. A plane acts as a two-dimensional surface where the sketch can be created. It provides the necessary foundation for drawing lines, shapes, and objects. Without a plane, it would not be possible to create a sketch in Inventor as there would be no surface to work on.Rate this question:
-
- 10.
The easiest way to make a sphere is to do what?
- A.
Extrude
- B.
Spline
- C.
Revolve
- D.
Fillet
Correct Answer
C. RevolveExplanation
To make a sphere, the easiest way is to use the revolve function. Revolving a 2D shape around an axis creates a symmetrical 3D object, such as a sphere. This process involves selecting a closed shape, like a circle, and specifying an axis of rotation. The software then generates a sphere by rotating the shape 360 degrees around the axis, creating a smooth and perfectly round object. Extruding, splining, or filleting would not result in a sphere shape as easily as the revolve function.Rate this question:
-
- 11.
The best tool to use to make irregular (curved) lines is
- A.
Spline
- B.
Extrusion
- C.
Chamfer
- D.
Circle
Correct Answer
A. SplineExplanation
The best tool to use to make irregular (curved) lines is a spline. A spline is a flexible line or curve that can be easily manipulated to create smooth and organic shapes. It allows for precise control over the shape and direction of the line, making it ideal for creating irregular or curved lines in design or drafting applications. Extrusion, chamfer, and circle are not specifically designed for creating irregular lines, but rather for other purposes such as creating 3D shapes or modifying edges.Rate this question:
-
- 12.
True or False: You should make your drawings for the same project in separate files.
- A.
True
- B.
False
Correct Answer
B. FalseExplanation
It is not necessary to make drawings for the same project in separate files. In fact, it is often more efficient and organized to keep all related drawings in a single file. This allows for easier access and reference to different parts of the project, and reduces the chances of losing or misplacing individual files. Additionally, having all drawings in one file promotes consistency and ensures that they are all easily accessible and located in a centralized location.Rate this question:
-
- 13.
Before you can make an Inventor presentation you must first make which of the following?
- A.
Parts and Drawings
- B.
Drawings and Assembly
- C.
Parts and Assembly
Correct Answer
C. Parts and AssemblyExplanation
To make an Inventor presentation, you need to have both parts and assembly. Parts refer to individual components or objects, while assembly refers to the arrangement or combination of these parts. By having both parts and assembly, you can effectively showcase the different components and how they come together to form a complete product or object in the presentation.Rate this question:
-
- 14.
True or False: It is ok to over-dimension your drawings.
- A.
True
- B.
False
Correct Answer
B. FalseExplanation
Over-dimensioning drawings means providing excessive or unnecessary dimensions that may confuse or mislead the reader. This can lead to errors in interpreting the drawing and cause problems during the manufacturing or construction process. It is important to provide only the necessary and relevant dimensions to ensure clarity and accuracy in the drawing. Therefore, it is not okay to over-dimension drawings.Rate this question:
-
- 15.
A(n) ___________ is a brand new idea or product that has never been thought of before.
Correct Answer
InventionExplanation
An invention refers to a brand new idea or product that has never been thought of before. It involves the creation of something completely original, unique, and innovative. Inventions often revolutionize industries, solve problems, or introduce new concepts. They require creativity, imagination, and the ability to think outside the box. Inventions can range from scientific discoveries to technological advancements, and they play a crucial role in driving progress and shaping the world we live in.Rate this question:
- 16.
Which of the following is NOT a type of engineering.
- A.
Nuclear
- B.
Aerospace
- C.
Mechanical
- D.
Electrical
- E.
All of the above are types of engineering
Correct Answer
E. All of the above are types of engineeringExplanation
All of the options listed in the question are actually types of engineering. Nuclear engineering involves the study and application of nuclear energy and radiation. Aerospace engineering focuses on the design and development of aircraft and spacecraft. Mechanical engineering deals with the design and production of mechanical systems and machines. Electrical engineering involves the study and application of electricity, electronics, and electromagnetism. Therefore, all of these options are valid types of engineering.Rate this question:
-
- 17.
What do you call a six sided figure?
- A.
Quadrilateral
- B.
Hexagon
- C.
Pentagon
- D.
Septagon
Correct Answer
B. HexagonExplanation
A six-sided figure is called a hexagon.Rate this question:
-
- 18.
What do you call a five sided figure?
- A.
Quadrilateral
- B.
Hexagon
- C.
Pentagon
- D.
Septagon
Correct Answer
C. PentagonExplanation
A five-sided figure is called a pentagon.Rate this question:
-
- 19.
What do you call a four sided figure?
- A.
Quadrilateral
- B.
Hexagon
- C.
Pentagon
- D.
Septagon
Correct Answer
A. QuadrilateralExplanation
A four-sided figure is called a quadrilateral. This term is derived from the Latin words "quadri" meaning "four" and "latus" meaning "side". Therefore, a quadrilateral is a polygon with four sides. Other options like hexagon, pentagon, and septagon refer to polygons with six, five, and seven sides respectively, which are not applicable in this case.Rate this question:
-
- 20.
What do you call a seven sided figure?
- A.
Quadrilateral
- B.
Hexagon
- C.
Pentagon
- D.
Septagon
Correct Answer
D. SeptagonExplanation
A seven-sided figure is called a septagon.Rate this question:
-
- 21.
Multiview drawings show:
- A.
Shape
- B.
Size
- C.
Size and Shape
- D.
None of the above
Correct Answer
C. Size and ShapeExplanation
Multiview drawings are a type of technical drawing that represent an object from different angles or views. These drawings include multiple views of the object, such as front, top, and side views. By including multiple views, multiview drawings provide information about both the size and shape of the object. This allows the viewer to understand the dimensions and proportions of the object accurately. Therefore, the correct answer is "Size and Shape."Rate this question:
-
- 22.
The right multiview goes where on the drawing sheet?
- A.
Top Left Corner
- B.
Top Right Corner
- C.
Bottom Right Corner
- D.
Bottom Left Corner
Correct Answer
C. Bottom Right CornerExplanation
The correct answer is "Bottom Right Corner" because traditionally, in engineering drawings, the top right corner is reserved for the title block which contains important information about the drawing such as the title, scale, and author. The bottom right corner is commonly used for auxiliary views or additional details that provide more information about the main view. Placing the right multiview in the bottom right corner allows for better organization and clarity in the drawing.Rate this question:
-
- 23.
Where does the top view go on a multiview drawing?
- A.
Top Right
- B.
Top Left
- C.
Bottom Left
- D.
Bottom Right
Correct Answer
B. Top LeftExplanation
In a multiview drawing, the top view is typically placed on the top left side. This is because in a multiview drawing, the views are arranged in a logical and consistent manner to provide a comprehensive representation of an object. The top view shows the object as it would appear from above, and it is conventionally placed on the top left side to maintain consistency with the arrangement of other views such as front, side, and bottom views.Rate this question:
-
- 24.
The best way to make a cone in Inventor is by using which of the following features?
- A.
Extrude
- B.
Loft
- C.
Sweep
- D.
Revolve
Correct Answer
D. RevolveExplanation
The best way to make a cone in Inventor is by using the Revolve feature. This feature allows the user to create a solid by revolving a sketch or profile around an axis. In the case of creating a cone, one can simply draw a half-profile of the cone and then use the Revolve feature to rotate it around a central axis to create a complete cone shape. This method ensures that the resulting cone is symmetrical and accurately represents the desired shape.Rate this question:
-
- 25.
True or False: the top multiview goes in the top right corner of the paper.
- A.
True
- B.
False
Correct Answer
B. FalseExplanation
The statement is asking whether the top multiview goes in the top right corner of the paper. The correct answer is false because the top multiview is typically placed in the top left corner of the paper.Rate this question:
-
- 26.
True or False: the front multiview goes in the lower left corner of the paper.
- A.
True
- B.
False
Correct Answer
A. TrueExplanation
The correct answer is true because in a front multiview, the front view of an object is placed in the lower left corner of the paper. This is a standard convention in technical drawing and drafting, where the front view is typically positioned in the lower left corner to provide a clear and consistent representation of the object.Rate this question:
-
- 27.
Engineers do all of the following except
- A.
Supervise
- B.
Manage
- C.
Design
- D.
Build
- E.
All of the above
- F.
None of the above
Correct Answer
E. All of the aboveExplanation
Engineers do not do all of the following: supervise, manage, design, and build. While engineers may supervise and manage projects, they do not necessarily perform all of the tasks involved in these roles. Similarly, while engineers may be involved in the design and construction process, they do not solely perform these tasks. Therefore, the correct answer is "All of the above."Rate this question:
-
- 28.
To create thin walls the best approach is to use which of the following?
- A.
Rib
- B.
Spline
- C.
Revolve
- D.
Loft
Correct Answer
A. RibExplanation
A rib is the best approach to create thin walls because it is a thin, elongated structure that provides support and strength to the walls. By using ribs, the walls can be made thinner without compromising their structural integrity. Ribs distribute the load evenly, preventing the walls from collapsing or bending under pressure. They also help in reducing material usage, making the structure more cost-effective. Therefore, using ribs is the most suitable method for creating thin walls.Rate this question:
-
- 29.
What is the first step of the design process?
- A.
Brainstorm
- B.
Identify a problem
- C.
Build a prototype
- D.
Share sketches
Correct Answer
B. Identify a problemExplanation
The first step of the design process is to identify a problem. This is because before any design can take place, there needs to be a clear understanding of what problem or need the design will address. By identifying a problem, designers can then begin to brainstorm and come up with possible solutions, build prototypes, and share sketches to further develop and refine their designs. However, without identifying a problem first, the design process cannot effectively begin.Rate this question:
-
- 30.
Why is the design process thought of as circular?
- A.
Circular objects are often the most popular types of designs
- B.
You must share your ideas with the team, allowing every team member to share their thoughts
- C.
You often become confused and that makes the room spin
- D.
You may have to go back and redo a step at any point in the process
Correct Answer
D. You may have to go back and redo a step at any point in the processExplanation
The design process is thought of as circular because it is not a linear process where each step is completed once and then the design is finalized. Instead, it is a continuous and iterative process where designers may have to revisit and redo certain steps multiple times. This is because new information, feedback, or ideas may arise throughout the process, requiring adjustments and refinements to be made. The circular nature of the design process allows for flexibility and improvement, ensuring that the final design meets the desired objectives.Rate this question:
-
- 31.
True or False: the diameter of a circle is half the size of the radius.
- A.
True
- B.
False
Correct Answer
B. FalseExplanation
The statement is false because the diameter of a circle is actually twice the size of the radius. The diameter is a straight line that passes through the center of the circle and touches two points on the circumference. In contrast, the radius is the distance from the center of the circle to any point on the circumference. Therefore, the diameter is always larger than the radius.Rate this question:
-
- 32.
You may have to do some research for this problem. True or False: a complete circle contains 365 degrees.
- A.
True
- B.
False
Correct Answer
B. FalseExplanation
A complete circle contains 360 degrees, not 365 degrees. This is a fundamental concept in geometry, where a circle is divided into 360 equal parts or degrees. Each degree represents 1/360th of the total angle in a circle. Therefore, the statement that a complete circle contains 365 degrees is false.Rate this question:
-
- 33.
An obtuse triangle has one angle
- A.
Equal to 90 degrees
- B.
Less than 90 degrees
- C.
More than 90 degrees
Correct Answer
C. More than 90 degreesExplanation
An obtuse triangle is a triangle that has one angle greater than 90 degrees. Therefore, the correct answer is "more than 90 degrees".Rate this question:
-
- 34.
An acute triangle has an angle
- A.
Equal to 90 degrees
- B.
Less than 90 degrees
- C.
More than 90 degrees
Correct Answer
B. Less than 90 degreesExplanation
An acute triangle is a triangle in which all three angles are less than 90 degrees. Therefore, the correct answer is "less than 90 degrees."Rate this question:
-
Quiz Review Timeline +
Our quizzes are rigorously reviewed, monitored and continuously updated by our expert board to maintain accuracy, relevance, and timeliness.
-
Current Version
-
Mar 21, 2023Quiz Edited by
ProProfs Editorial Team -
Mar 07, 2011Quiz Created by
Bluster
- Accreditation Quizzes
- Advanced Placement Quizzes
- AED Exam Quizzes
- Art Exam Quizzes
- Banking Exam Quizzes
- BISC Exam Quizzes
- CADET Exam Quizzes
- CAE Listening Quizzes
- CHS Exam Quizzes
- Computer Operator Exam Quizzes
- Cosmetology State Board Quizzes
- CSAT Quizzes
- CVS Exam Quizzes
- EHR Exam Quizzes
- Engineering Exam Quizzes
- English Exam Quizzes
- Entrance Exam Quizzes
- FSHN Exam Quizzes
- GATE Quizzes
- IGCSE Quizzes
- JEE Exam Quizzes
- Management Exam Quizzes
- Ministerial Exam Quizzes
- OCA Exam Quizzes
- Online Test Quizzes
- Physical Exam Quizzes
- Police Exam Quizzes
- Practice Exam Quizzes
- Prelim Exam Quizzes
- Professional Certification Quizzes
- SNAP Quizzes
- SSC Quizzes
- SSC CGL Quizzes
- UGC NET Exam Quizzes
- UPSC Quizzes
Back to top