Vignesh Uma Quiz -5

Approved & Edited by ProProfs Editorial Team
The editorial team at ProProfs Quizzes consists of a select group of subject experts, trivia writers, and quiz masters who have authored over 10,000 quizzes taken by more than 100 million users. This team includes our in-house seasoned quiz moderators and subject matter experts. Our editorial experts, spread across the world, are rigorously trained using our comprehensive guidelines to ensure that you receive the highest quality quizzes.
Learn about Our Editorial Process
| By Abhijai
A
Abhijai
Community Contributor
Quizzes Created: 2 | Total Attempts: 218
Questions: 15 | Attempts: 129

SettingsSettingsSettings
Vignesh Uma Quiz -5 - Quiz


Questions and Answers
  • 1. 

    Which statement is incorrect-

    • A.

      During refuelling after endurance Fuel pump must be turned off

    • B.

      during refuelling after endurance fuel valves must be opened

    • C.

      Team whose corrected elapsed endurance time exceeds Tmax may recive non zero points for efficiency.

    • D.

      When the second driver is fully secured in the vehicle, the vehicle has restarted the driver change time is stopped.

    • E.

      All are incorrect

    • F.

      1,3,4 are incorrect

    Correct Answer
    F. 1,3,4 are incorrect
  • 2. 

    Suppose 3 team member presented  Business Plan Presentation  for Team A,after the presentation during the question and answer session,team got stuck in one question asked by the judges and team member of the same team not part of initial business plan presentation team came running to the podium ,and answered the question correctly ,what will happen in such cases ??

    • A.

      .Nothing,as he was a team member

    • B.

      .it will not be accepted

    • C.

      5 points penalty

    • D.

      Disqualification from FSG

    • E.

      0 points for BPP

    • F.

      None of these

    Correct Answer
    B. .it will not be accepted
    Explanation
    If a team member who was not part of the initial business plan presentation team comes running to the podium and answers a question correctly during the question and answer session, their answer will not be accepted.

    Rate this question:

  • 3. 

    A team submitted SES on the last day of submission day,and after that they get officials request for 3 corrections in the document,the team submit the corrected document just before starting of 13th  days ,if the penalty for each 24 hours is 5 points after 168 hours ,what will be total penalty on the team ?

    • A.

      -30

    • B.

      -90

    • C.

      -25

    • D.

      -75

    • E.

      Disqualification

    • F.

      None of the above

    Correct Answer
    F. None of the above
    Explanation
    The team submitted the corrected document just before the starting of the 13th day, which means they submitted it within the 168-hour time frame. Therefore, they did not exceed the 168 hours, and no penalty points will be deducted. Hence, the total penalty on the team is none of the above.

    Rate this question:

  • 4. 

    What is the format and minimum file size to submit the structural equivalency 3D model for FSG?

    • A.

      IGES,30MB

    • B.

      IGES,20MB

    • C.

      IGES,40MB

    • D.

      SLDPRT,40MB

    • E.

      PARASOLID,40MB

    • F.

      None of the above

    Correct Answer
    F. None of the above
  • 5. 

    A team successfully cleared the FSG registration quiz and there were 26 teams on the waitlist then.They couldn’t afford the entry fees and deregistered from the event . However 20 hours later they got the funds and decided to go for the event.What will be their registration status?

    • A.

      They will be registered directly

    • B.

      De-registration is not allowed in FSG

    • C.

      Once deregistration is done, you cant register again

    • D.

      They will be 27th on the waitlist

    • E.

      They will be given wildcard entry

    • F.

      None of the above

    Correct Answer
    D. They will be 27th on the waitlist
    Explanation
    Since the team had already deregistered from the event, they will not be able to directly register again. Therefore, they will be placed back on the waitlist, but this time as the 27th team.

    Rate this question:

  • 6. 

    A team using RON98 fuel’s measured fuel volume consumption was 5.6L . Team B uses E85, Team A wanted to compare their fuel volume with Team B. So Team A’s fuel consumption when made comparable to TEAM B is , 

    • A.

      7.84L

    • B.

      5.6L

    • C.

      4L

    • D.

      6.4L

    • E.

      7L

    • F.

      You cant compare two fuels

    Correct Answer
    A. 7.84L
    Explanation
    Team A's fuel consumption when made comparable to Team B can be calculated by multiplying Team A's fuel consumption (5.6L) by the energy content ratio of RON98 fuel to E85 fuel. Since E85 has a lower energy content than RON98, the fuel consumption needs to be adjusted to account for this difference. Therefore, the correct answer is 7.84L.

    Rate this question:

  • 7. 

    During Endurance, a driver was driving recklessly and missed two slalom gates,then he was black flagged by the marshall which he ignored and completed endurance? What will be the total penalty only because of the above mentioned circumstances?

    • A.

      20 seconds

    • B.

      40 seconds

    • C.

      80 seconds

    • D.

      DNF

    • E.

      Official enquiry on the team

    • F.

      No penalty

    Correct Answer
    C. 80 seconds
    Explanation
    The driver in question missed two slalom gates and ignored a black flag from the marshal, indicating reckless driving. These actions would result in a penalty. The answer of 80 seconds suggests that this is the total penalty for the mentioned circumstances.

    Rate this question:

  • 8. 

    Which of the following is not true regarding monocoque attachment points ?

    • A.

      In any direction, each attachment point between the monocoque and the other primary structure must be able to carry a load of 30kN.

    • B.

      Data obtained from the laminate perimeter shear strength test should be provided

    • C.

      Each attachment point requires a minimum of two (2) 8 mm Metric Grade 8.8 bolts

    • D.

      Hand Calculations regarding this are not accepted anywhere

    • E.

      Each attachment point requires steel backing plates with a minimum thickness of 2 mm.

    • F.

      None of the above

    Correct Answer
    D. Hand Calculations regarding this are not accepted anywhere
    Explanation
    The statement that hand calculations regarding monocoque attachment points are not accepted anywhere is not true. Hand calculations are commonly used in engineering to analyze and design structures, including attachment points. Therefore, this statement is false.

    Rate this question:

  • 9. 

    A team uses SAE 4340 steel which is stronger than SAE 4130(assume), to make steel tubes for their front and main hoops.If they show physical testing,will they face difficulty in TI if the wall thickness is 1.4mm

    • A.

      No

    • B.

      It depends on the TI Inspector

    • C.

      No, if they can show documents proving that it is stronger

    • D.

      Cant Say

    • E.

      Yes

    • F.

      None of the above

    Correct Answer
    E. Yes
    Explanation
    The team will face difficulty in TI (Technical Inspection) if they use SAE 4340 steel with a wall thickness of 1.4mm for their steel tubes. This is because the strength of the steel alone is not the only factor considered in TI. The wall thickness also plays a crucial role in determining the structural integrity and safety of the tubes. A wall thickness of 1.4mm may not meet the required standards and regulations for TI, regardless of the strength of the steel used. Therefore, the team will face difficulty in passing TI with these specifications.

    Rate this question:

  • 10. 

    Which of the following is true about P1 ?Assume data to be obatained from Monocoque laminate testing 

    • A.

      The perimeter shear strength of the monocoque laminate in the front bulkhead support structure should be at least 4kN when determined at P1 for a section with a diameter of 25 mm

    • B.

      The perimeter shear strength of the monocoque laminate in the front bulkhead support structure can be less than 4kN at P1 for a section with a diameter of 25 mm

    • C.

      It is used to determine skin shear strength

    • D.

      The peak after P1 is used to determine skin shear strength

    • E.

      Both b and c

    • F.

      None of the above

    Correct Answer
    E. Both b and c
    Explanation
    The correct answer is "both b and c." This means that both options b and c are true about P1. Option b states that the perimeter shear strength of the monocoque laminate in the front bulkhead support structure can be less than 4kN at P1 for a section with a diameter of 25 mm. Option c states that P1 is used to determine skin shear strength. Therefore, both statements b and c are true about P1.

    Rate this question:

  • 11. 

    Let the ground clearance of a car be 50mm,where its lowest point is the inside point between the front hoop and main hoop.Then which of the following can be the height of the upper side impact member?

    • A.

      369mm

    • B.

      351mm

    • C.

      420mm

    • D.

      382mm

    • E.

      335mm

    • F.

      None of these

    Correct Answer
    E. 335mm
    Explanation
    The ground clearance of a car refers to the distance between the lowest point of the car and the ground. In this question, it is stated that the lowest point is the inside point between the front hoop and main hoop. Therefore, the height of the upper side impact member should be less than the ground clearance, as it is located above the lowest point. Among the given options, the only height that satisfies this condition is 335mm.

    Rate this question:

  • 12. 

    A team used composite material for manufacturing of body panels,the composite consisted  of 20 % carbon fiber ,20 % Kevlar and 60 % glass fiber ,they reported a cost of $200 for the panel ,but it was found that it had 30 % carbon fiber ,what  $penalty will be imposed?Assume total amount of fiber laid to be 13 m^2 and cost of carbon fiber is $30 per m^2,Kevlar is $40 m^2 and glass fiber be $50  m^2.  

    • A.

      Cost will be 1.25 of the initial reported cost

    • B.

      Cost will be 0.75 of the initial reported cost

    • C.

      Cost will be considered as $200 with 20 points penalty

    • D.

      Cost will be considered as $650

    • E.

      Depend on the judges

    • F.

      Disqualification from the event

    Correct Answer
    D. Cost will be considered as $650
    Explanation
    The penalty for using a higher percentage of carbon fiber than reported is that the cost of the panel will be considered as $650. This is because the cost of carbon fiber is $30 per m^2, and since the total amount of fiber laid is 13 m^2, the additional 10% of carbon fiber will result in an extra cost of $30 per m^2. Therefore, the total cost of the panel will be $200 + ($30 * 10% * 13) = $650.

    Rate this question:

  • 13. 

    In the cost report, which fit of the quick release for steering should be need to mentioned

    • A.

      Hand Fit

    • B.

      Fit is not mentioned in cost report

    • C.

      Loose Fit

    • D.

      Line on Line fit

    • E.

      Interference Fit

    • F.

      None of the above

    Correct Answer
    C. Loose Fit
    Explanation
    The cost report should mention the fit of the quick release for steering as "Loose Fit." This means that the quick release has some clearance and is not tightly fitted.

    Rate this question:

  • 14. 

    The tech inspection responsible person in a team is a member other than the registered captain and two deputies. He was unable to perform tech inspection as asked by inspector ?What action will be taken?

    • A.

      The captain will be asked to conduct TI immediately

    • B.

      The captain or the two deputies will be asked to conduct TI immediately

    • C.

      The member can be swapped with any other teammate

    • D.

      The TI will end and the team has to leave the area

    • E.

      Depends if the inspector gets irritated

    • F.

      None of the above

    Correct Answer
    D. The TI will end and the team has to leave the area
    Explanation
    If the tech inspection responsible person is unable to perform the tech inspection as asked by the inspector, the team will have to leave the area and the tech inspection will end. This is because the tech inspection is a crucial part of the process and if it cannot be conducted properly, the team cannot proceed further. The captain or the two deputies cannot conduct the tech inspection immediately as they are not the designated responsible person for it. Swapping the member with another teammate is not mentioned as an option, and the action taken does not depend on the inspector's irritation. Therefore, the correct answer is that the team has to leave the area and the tech inspection will end.

    Rate this question:

  • 15. 

    A team finished in the LAST postion in the BPP finals. What could be their minimum score amongst the following ?

    • A.

      70

    • B.

      71

    • C.

      Depends on Maximum score

    • D.

      0

    • E.

      35

    • F.

      None of the above

    Correct Answer
    B. 71
    Explanation
    The team finished in the last position in the BPP finals, which means they performed worse than all the other teams. Therefore, their score must be lower than any other team's score. Among the given options, the minimum score would be 0, as it is the lowest possible score.

    Rate this question:

Quiz Review Timeline +

Our quizzes are rigorously reviewed, monitored and continuously updated by our expert board to maintain accuracy, relevance, and timeliness.

  • Current Version
  • Mar 19, 2023
    Quiz Edited by
    ProProfs Editorial Team
  • Jan 13, 2017
    Quiz Created by
    Abhijai
Back to Top Back to top
Advertisement